RG74BF2 Frigidaire Wall Oven - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Replaced element. Removed shelves, removed two screws and lifted/wiggles old element out to pull wires off at connectors. Reversed process installing new element and truned on to test/burn off "newness" Done!

turned off power, removed 2 screws replaced heater coil tightened screws.

turned off main power; took a flash light, unscrewed existing element and disconnected it from the wiring; compared existing with new elements as the shipping label said "ABSOLUTELY NOTHING MAY BE RETURNED IF IT APPEARS THAT IT HAS BEEN INSTALLED"; it appeared to be close enough but not exact. Connected wiring to new element, shoved it back into the insultation, screwed in the element with the same screws. Viola' all worked as it should. I even set my oven on the "self clean" cycle which is 3 hours on high. Overall it was very easy.

Twisted replacement bulb into place easily. Let there be light!

first, I watched the video that partselect provides, then followed the instuctions that I learned from the video, I turned off the power to the appliance, removed the oven racks, removed the screws from the plate that held the oven rack in place and gently pulled it out far enough to remove the ends of the element from the electrical current wires, finished removing the burnt out element and replaced it with the new one from Partselect by repacing the new element ends on the electrical current wires and screwed it into place and replaced the racks, turned on the power and baked my pie. I am a 71 year old widow who was able to accomplish this with the good instructions provided by Partselect, this was the first time I have ever tried to do anything like this on my own.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

First removed the two screws that hold the element in place.I then pulled the element out about three inches and disconnected the two wires. The new element was put in place and reconnected to the two wires.The two screws to hold the element in place wre put back in.Very easy.

Pulled out the old light on the front of the door house where the door closes and replaced the door light switch

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Very easy just had to pull the wire up that holds it secure.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.