This screw, known as a handle fixer, is used to keep the door handles on your refrigerator secure. This screw is a genuine OEM part that comes individually, and simply screws into place in your refrigerator, and then allows the refrigerator handle to slide onto it. Your refrigerator normally has two of these fixer screws, so be sure to check how many you require before ordering.
The water in your home can contain impurities that affect its clarity, taste, smell, and safety. Water can contain dirt, rust, chlorine, or water-hardening minerals. These deposits can cause health issues, damage to your refrigerator, and leave your water and ice cloudy and undrinkable. This OEM water filter uses a block of activated carb...Read moreon to filter these pollutants out, giving you healthy, clear, great-tasting water and ice. This filter fits many Samsung refrigerators, and is rated NSF 42 and 53, which certifies that this fridge filter removes pollutants including: chlorine, cysts, asbestos, benzene, sediment, and sand. A good way to judge whether the filter needs to be replaced is when the water flow to the dispenser starts slowing down and there has been no change to the water pressure to the product. There is no bypass needed. Just remove the filter and it will automatically bypass the water filter. It has an easy twist design making the replacement quick and painless with no need for tools or mess. It measures 2.13 inches by 2.13 inches by 8.86 inches and weights 0.56 lbs. Replace every six months.
This French door hinge is an authentic OEM part used in refrigerators. It is used to provide support and stability to the door allowing it to open and close smoothly. The hinge is vulnerable to wear and tear, and mechanical damage over time. A faulty door hinge will result in difficulty opening/closing the door, door misalignment, inadequ...Read moreate sealing, and increased energy consumption. To begin this repair, locate the screws that hold the hinge to the refrigerator frame and remove them. Carefully lift the door off the hinge and set it aside. Remove the faulty hinge and position the new one in its place. Reattach the door to the new hinge and secure the hinge to the refrigerator frame using the appropriate fasteners.
This a genuine OEM temperature sensor, designed for use with refrigerators, and is an individual part. This temperature sensor is responsible for detecting and adjusting the temperature in your refrigerator. If your refrigerator is having issues with being either too cold, or too warm, it is likely that this sensor needs to be replaced. T...Read moreo replace it, ensure that your refrigerator is turned off before you locate it with your user manual and replace it.
This is an evaporator fan motor for a wide range of Samsung refrigerators. Evaporator fans pull warm air through evaporator coils to cool and maintain the internal temperature of the refrigerator. If the evaporator fan motor in your refrigerator is not working properly, your fridge will not cool properly and may even prevent the ice maker...Read more and water dispenser from working, and it will ultimately need to be replaced. This OEM evaporator fan motor measures approximately 4 inches long by 4 inches wide and will need a screwdriver and needle nose pliers to be removed and installed.
This is the end cap for the freezer door of various Samsung refrigerators. This end cap is made of plastic and features a brushed-metal finish, and simply snaps on or off the end of the freezer door handle. If your freezer door handle is missing its end caps, or if they are damaged, they should be replaced to give your door handle a more ...Read morefinished appearance. Most handles require two end caps, so be sure to consider how many end caps you require before ordering.
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evaporator fan motor is faulty, you will notice inconsistent internal temperatures, excessive and unusual noise, and frost build up. To begin th...Read moree repair, disconnect the refrigerator from power and remove all shelves and food items in front of the rear panel. Remove the mounting screws on the rear panel and carefully detach it to expose the fan motor. Disconnect the wire connectors to the motor and pull it out of the refrigerator. You may reuse the old fan blades if they are in good condition. Insert the new motor in the refrigerator and reattach the mounting screws. Reconnect the wire connector and reassemble the refrigerator in reverse order.
This ice maker assembly is for refrigerators. Ice maker assembly contains the complete ice maker and housing. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included. Safely store any food that could deteriorate while the power is off and unplug the refrigerator when installing this part. Wear work gloves to protect your hands.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Evaporator frozen (refrigrator section) and allowing top section to lose cooling
107 of 181 peoplefound this instruction helpful.
Richard from GULFPORT, MS
Easy
30 - 60 mins
Screw drivers
This is the Samsung French door refrigerator style that so many people have complained about freezing up and not cooling the top section. I first changed out the defrost thermostat and this did not correct the problem. I done a quick resistance check on the temp sensor that's mounted on the evaporator itself. The resistance would change w
... Read morehen holding an ice cube on the sensor so I just assumed it was ok. PLEASE TAKE NOTE: When performing a resistance check on this sensor, make sure your readings match the Samsung temp/resistance chart in their literature. My sensor was way off calibration and was causing the freeze up. Its working as designed now and DW is happy again. Learn from my mistake.
Read less
Was this helpful?
Thank you for voting!
Main refrigerator was not cooling down adequately.
14 of 15 peoplefound this instruction helpful.
James from VISALIA, CA
Easy
30 - 60 mins
Screw drivers
I looked up a YouTube video and it gave pretty well laid out instructions on how to replace the Twin fan assembly in the main compartment. There was also a suspicion that the sensor wasn't working properly and the fan had ice on it. Once I removed the main housing at the back of the inside of refrigerator it was relatively easy
... Read moreto replace the fan motor, and sensor. You have to follow the disassemble procedure closely in getting the main housing out. You have to remove the clear plate covering the water filter. Then remove the bottom shelf, which then gives you access to the large white back panel. After that its easy to replace the motor and sensor.