The French door divider spring fits most Samsung French door style refrigerators. The spring applies tension between components in the refrigerator, which engages and retracts the door flap. This will allow the door to close properly. If the spring is broken, damaged, or faulty the door flap will swing open and block the door from closing...Read more, and you should look to replace the part straight away to prevent further damage to the door. The spring is a genuine OEM part, is made of metal, and measures at 1 1/2 long. This part is also known as a refrigerator door mullion spring.
This is a door gasket, also known as a door seal, for Samsung refrigerators. This door gasket is used to create a barrier between the cooled interior temperature of the refrigerator, and the warmer temperature of your home. If this door gasket is warped or damaged in any way, you need to replace it immediately so your fridge can continue ...Read moreto cool optimally. To replace this gasket on your fridge, you simply need to pull off the old gasket, and carefully wrap this new one around the perimeter of the door. This gasket is sold individually and does not come with any other parts or accessories.
This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the cubs into the ice bin. This ice maker assembly is made of plastic and measures approximately 12 inches, long by 4.75 inches tall and 4.5 inch...Read morees wide. This ice maker is an OEM part that does not come with any other installation parts and attaches within the freezer compartment via its single wire harness.
This is an evaporator fan motor for a wide range of Samsung refrigerators. Evaporator fans pull warm air through evaporator coils to cool and maintain the internal temperature of the refrigerator. If the evaporator fan motor in your refrigerator is not working properly, your fridge will not cool properly and may even prevent the ice maker...Read more and water dispenser from working, and it will ultimately need to be replaced. This OEM evaporator fan motor measures approximately 4 inches long by 4 inches wide and will need a screwdriver and needle nose pliers to be removed and installed.
This evaporator fan motor is sourced from the original manufacturer for use in refrigerators. It circulates cold air throughout the refrigerator compartment to maintain consistent cooling. If the evaporator fan motor is faulty, you will notice inconsistent internal temperatures, excessive and unusual noise, and frost build up. To begin th...Read moree repair, disconnect the refrigerator from power and remove all shelves and food items in front of the rear panel. Remove the mounting screws on the rear panel and carefully detach it to expose the fan motor. Disconnect the wire connectors to the motor and pull it out of the refrigerator. You may reuse the old fan blades if they are in good condition. Insert the new motor in the refrigerator and reattach the mounting screws. Reconnect the wire connector and reassemble the refrigerator in reverse order.
This is a power cord made for Samsung refrigerators. If your current power cord is damaged, broken, or no longer supplying power to your fridge, you can disconnect it from the wall outlet, strip it from your fridge, and replace it with this OEM cord. This power cord is sold individually and does not include any other parts or accessories.
Introducing the genuine Samsung Fan Blade Assembly, a premium quality replacement part for your refrigerator. Designed to keep your appliance cool and functioning at optimum levels, this high-quality assembly is user-friendly and equips with all necessary hardware for easy installation. The essence of this assembly becomes evident when yo...Read moreur refrigerator isn't cooling sufficiently, which is usually due to faulty running fan motors or damaged fan blades. This fan blade assembly effectively moves air across the condenser coil, cooling the hot refrigerant before it infiltrates the evaporator. Ensure to safeguard any food that may deteriorate during a power-off scenario and disconnect your refrigerator prior to installing this part. Embrace your Samsung refrigerator with this fan assembly for a smooth, trouble-free functioning.
This Samsung hex screw is a genuine OEM replacement fastener that is designed for the refrigerator door handle. It is a stainless steel screw that secures the handle to the refrigerator door. It is responsible for providing stability and support to the handle to ensure that the handle remains firmly attached and functional. Over time the ...Read moremounting screw may fail, typically due to wear and tear, accidental damage, or corrosion, and the handle may become loose or detach completely. A loose or detached handle can make it difficult to open or close the fridge door properly. Additionally, an unstable handle can cause damage to the door or handle mechanism, which can result in further costly repairs. Therefore, it is recommended to replace the mounting screw(s) promptly to ensure you can continue to use and enjoy your refrigerator. Be careful not to overtighten the screw during the repair as this can damage the handle and mounting surface. Each hex screw is sold individually.
This white-colored flipper or mullion assembly serves as a seal mechanism found between the French doors of your refrigerator. It measures 36 inches in length and 2 inches in width. Positioned along the inner edge of one door, it flips into place to close the gap when the doors meet. A broken assembly might result in loose door closure an...Read mored escaping cold air, so it is important to replace it to keep your food fresh. This genuine OEM replacement part is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Installation Video Incorrect
34 of 44 peoplefound this instruction helpful.
Cheryl from PALATINE, IL
A Bit Difficult
30 - 60 mins
Pliers
The installation video notes that the door mullion spring has a bent end, and that the bent end of the spring is to be inserted into the LOWER hinge. However, on my refrigerator door, the bent end of the door mullion spring must be inserted into the UPPER hinge in order for the door to function properly. (Also noted that in your video t
... Read morehe installer manually closed the door mullion rather than just closing the refrigerator door, another indication that the installation of the spring was incorrect.) After watching the video several times to confirm I was installing the door mullion spring according to the video instructions, I tried inserting the bent end of the door mullion spring into the upper hinge, which proved to be the correct installation of the door mull spring. What should have been a 5 minute repair turned into an ½ hour repair.
Read less
Was this helpful?
Thank you for voting!
Door Mullion Spring broke
11 of 21 peoplefound this instruction helpful.
Linda from OAKLEY, CA
Very Easy
Less than 15 mins
Went to You Tube and saw video on how to replace broken mullion spring. Ordered part online (more than one in case one broke -very cheap <$3.00 per part). Watched video twice and was able to follow instructions and insert spring correctly. Not difficult if you pay attention to details on how the spring must fit and which end goes wher
... Read moree. The door works perfectly!
Read less
Was this helpful?
Thank you for voting!
spring in door mullion had broken
12 of 25 peoplefound this instruction helpful.
Gary from TUPPER LAKE, NY
A Bit Difficult
1- 2 hours
Pliers
There is a pretty good video about this on youtube, but complications arose nonetheless. The replacement spring supplied by Partselect is a bit different from the original in two ways. First, it is made of heavier-gauge wire; this is a good thing for durability, but it makes installation tougher. Second, the ends of the spring, which a
... Read morere bent at right angles to the spring axis in order to fit into the plastic sleeves that hold the spring ends, are far too long. Once I figured this out, i snipped the ends down by a quarter inch or so, and they fit into the sleeves just fine after a certain amount of persuasion from needle-nose pliers. All things considered, it was a bit harder than it should have been, but the door works now, so all is well.
My Orders
