Quick Question!

Have you ever purchased from PartSelect.com before?

Models > REX4625EN0

REX4625EN0 Roper Dryer - Overview

Get Parts and Repair Help for REX4625EN0

If you know the dryer repair part you need, you can browse the list of all parts on the REX4625EN0, or you can search by name or part description. You can also find your part by where it is located on the REX4625EN0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for REX4625EN0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the REX4625EN0

[Viewing 3 of 3]

Manuals & Care Guides for REX4625EN0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.98

Thermal Fuse

This thermal fuse is designed for use in dryers. It is a safety mechanism that stops the flow of electricity to the heating element when a dryer overheats. When this fuse is faulty...

$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the motor rotates, the belt begins to move and turns the drum. If you notice the drum of your dryer is not spinning during the dry cycle, but you hear the motor running, your belt may have snapped and it will need to be replaced. This belt features four ribs and three grooves, however it replaces a wide variety of belts including wider styles that had five ribs and four grooves. When installing this part make sure the grooves are facing down, against the drum. This replacement part is 92 1/4 inches in length, and 1/4 inch wide. Before you begin any repair work, make sure your dryer has been unplugged.

$61.75

Heating Element - 240V 5400W

The heating element is strung with a coiled wire that is made out of a nickel and chrome alloy. The function of the coiled wire on the heating element is to receive and resist a co...

$35.86

Thermal Cut-Off Kit

The thermal cut off turns off the heating component when the dryer overheats, ensuring there is a consistent level of heat at all times. This dryer thermal cut-off kit includes one high-limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires. If your dryer is not starting properly, shutting off too soon or is taking too long to dry your clothes it could be because it has blown and needs to be replaced. This is a genuine OEM part that comes directly from the manufacturer.

$12.47

Rear Drum Support Roller Kit

The drum support roller kit allows the dryer to tumble properly by supporting the drum cylinder. The kit includes two drum rollers, four tri-rings and one palnut (or retaining wash...

$10.04

Idler Pulley Assembly

This part provides the tension required for a multi-ribbed belt. It also serves to help the belt to rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long to dry, or is noisy during operation, you may need to replace the idler pulley assembly. Make sure to disconnect power before installing this part, and work gloves are recommended to protect your hands. While the dryer is disassembled for this repair, consider replacing the drive belt as well. You will need a putty knife, a Phillips screwdriver and a 5/16 nut driver for this repair.

$5.76

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found b...

$4.94

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

$24.56

Lint Filter

This filter collects lint as it passes through the dryer vent.

$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Keep the washer as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This replacement part is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2149 of 2417 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

Dryer motor runs, but no heat

  • Customer: Gadi from Irvine, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1995 of 2148 people found this instruction helpful
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element with an ohm-meter or v... read more

Dryer tub belt broke

  • Customer: Ray from Denton, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 860 of 913 people found this instruction helpful
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are ... read more