RD906812A Ridgid Generator - Overview

This inline fuel filter is a genuine OEM part designed for use with pressure washers and generators and is sold as an individual part. Made of plastic, this filter is used to prevent dirt and debris from entering the carburetor and engine of your equipment. Regular maintenance, routine inspections, and replacement of this part will help t...Read moreo prevent any issues with your equipment in the future and ensure best performance. If your equipment is experiencing starting issues or you notice blue or dark-colored smoke coming from your equipment, the filter may need to be replaced. To replace your current filter, gain access to the fuel line or tank, restrict the flow of fuel through the filter, and simply remove it before replacing it. If your filter needs replacing, check your fuel lines for any clogs or debris build-up.

This vapor vent, also known as a vent valve or vent cap, is supplied by the original manufacturer for use with generators. It is designed to provide ventilation for the fuel tank by allowing air to enter and leave the tank as necessary. The vent prevents pressure from building up in the tank and interfering with the flow of fuel. Over tim...Read moree the vent may become clogged, or damaged leading to hard starting, fuel leakage, stalling, and the release of harmful gases into the atmosphere. It is recommended to inspect the vent before each use and replace any blocked vent promptly. To complete this repair, remove the faulty vent from the fuel tank and clean the mounting area. Thread the new vent on to the tank and ensure it is locked in place.

This fuel shut-off valve, also known as a fuel valve or fuel selector valve, is an OEM replacement part designed for use in generators. The valve controls the flow of fuel to the engine. When the valve is in the on position, fuel flows to the engine, enabling it to run. When the valve is in the off position the flow of fuel stops and the ...Read moregenerator shuts down. Over time the valve may become clogged or damaged, and unable to fully close or open. Once the fuel shut off valve is no longer functioning, the generator will leak fuel, and may have difficulty in starting or running. Before replacing the valve, first disconnect the fuel line and place a container below the fuel tank to allow the fuel to drain out. Detach the old fuel shut off valve and install the new one in its place. Apply thread sealant to the new valve for a good seal and reattach the fuel line. Refill your tank with fresh fuel and run the equipment to ensure there are no more leakages.

This is a genuine manufacturer-sourced component that is specially designed for use with Ryobi, Ridgid and Homelite equipment. It is an identical replacement for a missing or faulty switch that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicati...Read moreon of this item. Keep in mind this high-quality plastic body switch is sold individually.

This OEM replacement washer is a thin, flat, round-shaped metal disk with a hole in the center, used in a variety of outdoor power equipment. It is made of steel and has an inner diameter of 0.25 inches. Washers are designed for use with fasteners such as bolts or screws to distribute the clamping force of the fastener and provide additio...Read morenal security to the parts being fastened. Additionally, they protect the surface they are positioned on from damage and can be used to align/level various components. You will need to replace your washer if it is corroded, cracked, or worn down. Each washer is sold individually.

This is a genuine Homelite, Ridgid, and Ryobi replacement part for use in generators. The fuel cap attaches to the fuel tank. No tools should be needed during the replacement of this part. It is made out of metal and will need to be replaced if it breaks. This item is sold individually.

The fuel tank vapor vent attaches to the bushing rollover valve and the fuel tank. This is a genuine Homelite and Ridgid part sourced directly from the manufacturer for use in generators. It is sold individually and is made out of plastic. During the installation process, a wrench and a set of pliers might be needed to replace this item. This part will need to be replaced if it breaks.

This replacement wheel and tire assembly is specially designed for Ridgid generators. It is an authentic OEM supplied part, not an aftermarket equivalent. It helps to keep your generator mobile for easy transportation. This assembly consists of a metal rim and and rubber tire. Please note, the axle bolt is sold separately.

This authentic item is supplied directly from the original equipment manufacturer for use with pressure washers and generators. The wear pad is made of hard rubber and attaches to the foot bracket with a washer and a bolt. It may require a wrench during replacement if the part becomes broken. The pad is sold individually and helps to reduce vibrations and cushion the bracket.

This replacement automatic voltage regulator is sourced directly from original equipment manufacturer for use with Homelite and Ridgid generators. It regulates the output voltage of the generator by limiting the amount of voltage in the electrical system. Please note this high quality item is sold individually.

This is an authentic manufacturer-sourced replacement washer which is specially designed for use with pressure washers. The purpose of this part is to provide a tight seal between connected components, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of ...Read moreyour model for the correct location and application of this hardware. Keep in mind this high-quality washer is made of durable metal and is sold individually.