RD905712B Ridgid Generator - Overview

This inline fuel filter is a genuine OEM part designed for use with pressure washers and generators and is sold as an individual part. Made of plastic, this filter is used to prevent dirt and debris from entering the carburetor and engine of your equipment. Regular maintenance, routine inspections, and replacement of this part will help t...Read moreo prevent any issues with your equipment in the future and ensure best performance. If your equipment is experiencing starting issues or you notice blue or dark-colored smoke coming from your equipment, the filter may need to be replaced. To replace your current filter, gain access to the fuel line or tank, restrict the flow of fuel through the filter, and simply remove it before replacing it. If your filter needs replacing, check your fuel lines for any clogs or debris build-up.

This vapor vent, also known as a vent valve or vent cap, is supplied by the original manufacturer for use with generators. It is designed to provide ventilation for the fuel tank by allowing air to enter and leave the tank as necessary. The vent prevents pressure from building up in the tank and interfering with the flow of fuel. Over tim...Read moree the vent may become clogged, or damaged leading to hard starting, fuel leakage, stalling, and the release of harmful gases into the atmosphere. It is recommended to inspect the vent before each use and replace any blocked vent promptly. To complete this repair, remove the faulty vent from the fuel tank and clean the mounting area. Thread the new vent on to the tank and ensure it is locked in place.

This guide bar nut is sourced from the original equipment manufacturer for use in chainsaws. It is made of metal, and has a diameter of 5/16 of an inch and a thread pitch of 18 threads per inch. The guide bar nut also has a flange on one end for added stability and security. The nut is responsible for holding the guide bar and chain in pl...Read moreace and ensures proper tension and alignment of the chain, for safe and efficient cutting. A faulty guide bar nut will result in the chain becoming loose or detached during operation, which poses a safety risk to the user. Additionally, a loose chain will result in reduced cutting ability, and damage to the guide bar. It is recommended to check your equipment manual for the correct number of guide bar nuts needed. Each nut is sold individually. Use a socket tool to loosen and remove the old nut. Clean the area around the guide bar and thread to ensure a good fit, and then insert the new nut and tighten it securely. Ensure that the chain is adequately tensioned before attempting to use the chain saw again.

This fuel shut-off valve, also known as a fuel valve or fuel selector valve, is an OEM replacement part designed for use in generators. The valve controls the flow of fuel to the engine. When the valve is in the on position, fuel flows to the engine, enabling it to run. When the valve is in the off position the flow of fuel stops and the ...Read moregenerator shuts down. Over time the valve may become clogged or damaged, and unable to fully close or open. Once the fuel shut off valve is no longer functioning, the generator will leak fuel, and may have difficulty in starting or running. Before replacing the valve, first disconnect the fuel line and place a container below the fuel tank to allow the fuel to drain out. Detach the old fuel shut off valve and install the new one in its place. Apply thread sealant to the new valve for a good seal and reattach the fuel line. Refill your tank with fresh fuel and run the equipment to ensure there are no more leakages.

This is a genuine manufacturer-sourced component that is specially designed for use with Ryobi, Ridgid and Homelite equipment. It is an identical replacement for a missing or faulty switch that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicati...Read moreon of this item. Keep in mind this high-quality plastic body switch is sold individually.

This OEM replacement washer is a thin, flat, round-shaped metal disk with a hole in the center, used in a variety of outdoor power equipment. It is made of steel and has an inner diameter of 0.25 inches. Washers are designed for use with fasteners such as bolts or screws to distribute the clamping force of the fastener and provide additio...Read morenal security to the parts being fastened. Additionally, they protect the surface they are positioned on from damage and can be used to align/level various components. You will need to replace your washer if it is corroded, cracked, or worn down. Each washer is sold individually.

This authentic manufacturer-sourced part is specially designed for use with portable generators. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The part helps to secure fuel tank to the main frame, please make sure to refer to the appropriate diagrams of your model for the correct loca...Read moretion and application of this hardware. Keep in mind this high-quality isolator is made of durable rubber and is sold individually.

This is a genuine Homelite, Ridgid, and Ryobi replacement part for use in generators. The fuel cap attaches to the fuel tank. No tools should be needed during the replacement of this part. It is made out of metal and will need to be replaced if it breaks. This item is sold individually.

This part is a 20 amp, 120 volts AC, circuit breaker which also includes two metal Phillips-head screws, two washers, and a bolt. The circuit breaker goes in the stationary control panel box and is designed to cut off the power if there is an overload. This metal part is an OEM for use in generators. It is time to replace this circuit breaker if the button is out and remains out even after being pushed in.

This authentic item is supplied directly from the original equipment manufacturer for use with pressure washers and generators. The wear pad is made of hard rubber and attaches to the foot bracket with a washer and a bolt. It may require a wrench during replacement if the part becomes broken. The pad is sold individually and helps to reduce vibrations and cushion the bracket.

This replacement automatic voltage regulator is sourced directly from original equipment manufacturer for use with Homelite and Ridgid generators. It regulates the output voltage of the generator by limiting the amount of voltage in the electrical system. Please note this high quality item is sold individually.