RD8000 Ridgid Generator - Overview

This inline fuel filter is a genuine OEM part designed for use with pressure washers and generators and is sold as an individual part. Made of plastic, this filter is used to prevent dirt and debris from entering the carburetor and engine of your equipment. Regular maintenance, routine inspections, and replacement of this part will help t...Read moreo prevent any issues with your equipment in the future and ensure best performance. If your equipment is experiencing starting issues or you notice blue or dark-colored smoke coming from your equipment, the filter may need to be replaced. To replace your current filter, gain access to the fuel line or tank, restrict the flow of fuel through the filter, and simply remove it before replacing it. If your filter needs replacing, check your fuel lines for any clogs or debris build-up.

This fuel shut-off valve, also known as a fuel valve or fuel selector valve, is an OEM replacement part designed for use in generators. The valve controls the flow of fuel to the engine. When the valve is in the on position, fuel flows to the engine, enabling it to run. When the valve is in the off position the flow of fuel stops and the ...Read moregenerator shuts down. Over time the valve may become clogged or damaged, and unable to fully close or open. Once the fuel shut off valve is no longer functioning, the generator will leak fuel, and may have difficulty in starting or running. Before replacing the valve, first disconnect the fuel line and place a container below the fuel tank to allow the fuel to drain out. Detach the old fuel shut off valve and install the new one in its place. Apply thread sealant to the new valve for a good seal and reattach the fuel line. Refill your tank with fresh fuel and run the equipment to ensure there are no more leakages.

This is is a genuine OEM sourced replacement brush assembly designed for use with generator motors. This assembly secures carbon brushes around the armature and provides stable and safe contact. This assembly includes: plastic holder, two (2) carbon brushes with lead wires and springs attached. To replace this assembly you would need a s...Read moreet of wrenches. • First remove screws holding the cover together • Carefully separate housing to gain access to armature and brush holder • Disconnect wires from old brushes • Remove old brushes and install the new assembly • Reassemble and test the motor

This OEM replacement washer is a thin, flat, round-shaped metal disk with a hole in the center, used in a variety of outdoor power equipment. It is made of steel and has an inner diameter of 0.25 inches. Washers are designed for use with fasteners such as bolts or screws to distribute the clamping force of the fastener and provide additio...Read morenal security to the parts being fastened. Additionally, they protect the surface they are positioned on from damage and can be used to align/level various components. You will need to replace your washer if it is corroded, cracked, or worn down. Each washer is sold individually.

This replacement part is sourced directly from original equipment manufacturer. This switch is designed for use with a variety of power equipment. It is an important piece of hardware responsible for handling on/off function of equipment. Because switches have internal mechanical part, over time they will break down requiring replacement....Read more This switch has a plastic body and it includes a clear plastic cover. To complete this repair you would need a screwdriver. • First make sure the unit is not plugged in • Then you want to separate housing pieces by removing screws • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit

This part is a 20 amp, 120 volts AC, circuit breaker which also includes two metal Phillips-head screws, two washers, and a bolt. The circuit breaker goes in the stationary control panel box and is designed to cut off the power if there is an overload. This metal part is an OEM for use in generators. It is time to replace this circuit breaker if the button is out and remains out even after being pushed in.

This replacement wheel and tire assembly is specially designed for Ridgid generators. It is an authentic OEM supplied part, not an aftermarket equivalent. It helps to keep your generator mobile for easy transportation. This assembly consists of a metal rim and and rubber tire. Please note, the axle bolt is sold separately.

This authentic item is supplied directly from the original equipment manufacturer for use with pressure washers and generators. The wear pad is made of hard rubber and attaches to the foot bracket with a washer and a bolt. It may require a wrench during replacement if the part becomes broken. The pad is sold individually and helps to reduce vibrations and cushion the bracket.

This replacement automatic voltage regulator is sourced directly from original equipment manufacturer for use with Homelite and Ridgid generators. It regulates the output voltage of the generator by limiting the amount of voltage in the electrical system. Please note this high quality item is sold individually.

This genuine Ridgid part is supplied by the original equipment manufacturer for use on portable generators. The fuse attaches to the control board to protect the circuit in an event of an overload. If this part burns out it will need to be replaced. Make sure to refer to the owner's manual for your model to ensure the correct repair procedure. Note, this high-quality fuse is sold as an individual item.