Sold individually. This bulb is a 7-watt appliance incandescent light bulb. This appliance light bulb is two inches long. It is used for many clothes dryers. You will need a Phillips screwdriver and needle-nose pliers. Unplug the power from your dryer. You will find the light bulb by opening your dryer door and locating the casing surroun...Read moreding the bulb on the top of the inside of the door. You will need to remove the single screw holding it in place to access the bulb. Twist the old bulb out of place. Use your pliers if the base of the bulb is still inside the socket once the glass part of the bulb has been removed. Check to make sure that the socket itself is not damaged. If the socket is damaged it will need to be replaced as well. Screw your new bulb into place.
Facing issues with your range? The GE Surface Element Control Switch might be just what you need to get your appliance up and running smoothly again. This key component accomplishes a significant task?controlling the temperature of the surface element and switching it on and off as needed. By adjusting the heat your element generates, i...Read moret plays a pivotal role in cooking your meals to perfection. Remember, safety is paramount when you're dealing with appliances. Before starting the replacement process, make sure to unplug your range or switch off the circuit breaker linked to it. Donning work gloves can provide you with an extra layer of protection, decreasing the chance of mishaps during installation. Rest assured knowing that the GE Surface Element Control Switch, like all GE products, is designed with top-notch engineering and reliability in mind - turning your range into a dependable appliance for years to come. Please verify your range model to ensure compatibility with the GE Surface Element Control Switch. The reward? A seamless cooking experience making your kitchen routines enjoyable again. Cheers to delicious meals and a healthy appliance!
This part may appear different than the original, but will function the same. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.
This white fresh food door gasket measures approximately 20 inches by 60 inches. It is all white in color and is made of rubber. This gasket is used for the fresh food door of many side by side model refrigerators.
The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold and to the water dispenser.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator fresh food side warm, freezer frosted over
21 of 26 peoplefound this instruction helpful.
Ernest from Shelby, MI
A Bit Difficult
More than 2 hours
Nutdriver, Pliers, Screw drivers
First did the easy part, removed and replaced the defrost timer. Didn't correct the problem.
Then got into the defrost heaters. Big job, because the factory didn't provide for repairs. Had to remove the ice maker because there was one screw holding on the cover panel behind it. The factory installed defrost heaters were run beh
... Read moreind the freezer coils so I had to cut them out. Then I had to bend the light aluminum sides with heavy pliers to slip the burned out defrost heaters out and replace them with the new defrost heaters. Didn't use the defrost timer, because I was taking it one step at a time.
Now the refrigerator fresh food side maintains 39 degrees and runs 1/10 the time it was running. My wife says it's better than new! Saved $ 2,400 (the replacement she had picked out).
Read less
Was this helpful?
Thank you for voting!
Refrigerator was freezing up and not cooling!
14 of 17 peoplefound this instruction helpful.
Garryl from Carleton, MI
Really Easy
15 - 30 mins
Pliers, Screw drivers
Well first I noticed the back of the freezer compartment freezing up and the ice not freezing. I moved all the contents of the freezer to another freezer. I waited and noticed even when pluged in and everything defrosted the fan didn't kick on on the condensing unit! After a few minutes it did kick on and I took a guess that the defrost t
... Read moreimer was probally ok without checking it. I took eight screws out of the back plate and noticed the defrosting tube on the lower part of the coil was broke in half. I knew I had found the problem. It took maybe 10 minutes to remove and about 10 minutes to order the part. Three days later it was at my door. I took my time installing it which only took maybe 30 minutes. It took longer for me to wipe everything down and clean the inside of both compartments than it did to insall the part. Pluged it in and fired it up and problem solved. Thanks Part Select!
Read less
Was this helpful?
Thank you for voting!
Meat drawer guide rail broken
8 of 9 peoplefound this instruction helpful.
Robert from Kelso, WA
Really Easy
Less than 15 mins
although this piece s white, my refrigerator had clear plastic guides - both work OK. Remove meat drawer, remove glass shelf from refrigerator. Glass shelf is attached to metal frame by two clips at rear of shelf. Before removing, notice how the clips are fastened to the chrome trim so replacement will be easier. Remove clips with fingers
... Read more. Glass shelf will then swing up and away from metal frame, allowing easy removal of drawer guide(s). Remove broken guide and replace with new. Lower the glass and re-attach metal clips. Replace metal shelf in refrigerator and re-insert drawer. That's it.