Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RB757WT4WW

RB757WT4WW Hotpoint Range - Overview

Get Parts and Repair Help for RB757WT4WW

If you know the range repair part you need, you can browse the list of all parts on the RB757WT4WW, or you can search by name or part description. You can also find your part by where it is located on the RB757WT4WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RB757WT4WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RB757WT4WW

[Viewing 5 of 5]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$37.57

Bake Element

At the floor of your electric oven is the bake element. This partially open-style element comes with push-on terminals. The bake element will likely provide most of the heat for ba...

$37.73

Surface Element - 8" - 2350W

The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.

$27.95

Surface Element - 6" - 240V

If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner el...

$5.30

Single Heating Element Support Clip

The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip is broken then this replacement should be the solution. The tools needed for this project are slip joint pliers. For safety precautions, make sure to unplug your range from the power source, or shut off the house circuit breaker before starting this project. Refer to the installation instructions for best results and accuracy.

$7.47

Surface Burner Drip Bowl - 6"

This chrome drip bowl is sold individually.

$5.05

Surface Burner Drip Bowl - 8"

$108.02

Oven Sensor

It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on ...

$3.38

SCREW

Sold Individually.

$53.82

Surface Burner Terminal Block Kit

This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and...

$33.20

Hinge with Roller - Right Side

This is a hinge with roller for the oven door on your range. The roller allows you to open and close the door with ease and control. If your door is not opening easily, you may need to replace this part. To make this repair you will need a Phillips screwdriver and a pair of pliers. Take note that this model is only for the right-hand side of your unit, to replace the left-hand side, see the related parts section. We recommend replacing both hinges at the same time.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake element cracked on its own

  • Customer: Timothy from Cordova, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 595 of 600 people found this instruction helpful
Flipped the breaker. Removed shelf, Find the right size nut socket, unscrew the two screws, pull the element out a little bit, disconnect the wires (on pretty tight), pull out element, clean out any mess in the oven, compare element with new one to make sure its the same size and such, connect wires to new element, replace screws, flip breaker back, tur... read more

Oven took 30 minutes to get to 380 degrees-no hotter

  • Customer: Sandra from Hayward, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 379 of 382 people found this instruction helpful
First I searched this site and read about the repairs - which made me feel like my husband could do it with ease. Then he removed two screws inside the oven, removed the broken element (didn't know it was broken til removed) and replaced the new one - just like that! The real key was being able to read how it was for other people who had already done it. ... read more

Oven tempature was approximately 150 degrees to low

  • Customer: James from Austin, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 200 of 228 people found this instruction helpful
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees t... read more