The drip bowl on your range is designed to catch any spills that may occur when cooking. This drip bowl is chrome in color and is 6 inches in diameter. The chrome drip bowl is intended for use with rolled, terminal-style plug-in surface element units. The drip bowl is located beneath the surface element, so you will need to remove the ele...Read morement prior to swapping out the old drip bowl for a new one. Many of our customers have rated this repair as easy, and you will not require any tools to complete it. This part is sold individually.
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside your range. This 8 inch chrome drip bowl fits most electric ranges. Before you replace your damaged drip bowl, make sure the element is turned ...Read moreoff and cool to the touch. Installation is easy, just remove the element, replace the current drip bowl, and reattach the element. Make sure the small hole on the bowl lines up with the element socket. Drip bowls are sold separately.
This part is the replacement surface burner or element for your range. It is approximately 8 inches in diameter, and 2100 watts. The surface burner connects to the power source and when it is turned on, it heats up to cook your food. If you turn on the burner and the element does not heat up, it will need to be replaced. To complete this ...Read morerepair, first be sure to disconnect the power from your range, and ensure the burner is cool to the touch. Then, gently remove the burner from the terminals and replace it with the new one. This part is sold individually, and is an OEM part sourced directly from the manufacturer.
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface burner terminal block kit connects the wiring harness to the surface elements. It is important to shut off the power to the appliance befor...Read moree starting this repair. You will need to remove all four elements, trim rings, and drip bowls to access the terminal block on your stovetop. This is an OEM replacement part that is sourced from the genuine manufacturer.
This is the replacement indicator light kit for your range. It contains 5 pieces including 2 wires, the lens, the washer, and the indicator light. The indicator light kit contains everything you need to get your indicator light to work properly. The indicator light becomes illuminated when the oven or cooktop is on. If you turn your cookt...Read moreop on and the indicator light does not light up, you may need to replace it. Be sure to check the control knobs for damage as well. This is an authentic OEM part sourced directly from the manufacturer.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
There was no heat on the coils.
48 of 52 peoplefound this instruction helpful.
Shaohui from East Lansing, MI
Easy
15 - 30 mins
Pliers
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Was this helpful?
Thank you for voting!
Surface burner coil did not work.
23 of 33 peoplefound this instruction helpful.
Gregory from Mont Belvieu, TX
Easy
30 - 60 mins
Nutdriver, Screw drivers, Socket set
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet
... Read more, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Read less
Was this helpful?
Thank you for voting!
Could not find the correct replacements (burners & drip pans)
13 of 21 peoplefound this instruction helpful.
Barbara from JEFFERSON, GA
Very Easy
Less than 15 mins
After months of buying the wrong parts & cost I discovered this site So easy to order & quick delivery, plus very easy installation. Thank you. I also wanted to add that the reps (Tanisha & Matthew) were extremely helpful & informative. I can only hope all the reps equal their performance. I will definitely be using this site, before an
... Read morey other source. Knowledge & cost is also important to me & that need was met. Good job!