This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends).
This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.
The manufacturer certified Foam Air Filter is a black, foam part, used to filter out contaminents from entering the carburetor. It attaches in the air cleaner housing, is rated as "Easy" to install, and requires a screw driver (Tip: put a bit of two-cycle oil in the bag, and let it absorb into the filter). If the part wears out, the engin...Read moree will burn more fuel and you will have noticably less power because it will be starved for air. If this happens, the part must be replaced. Refer to your make, model and diagram to ensure this air filter is correct for your machine.
This OEM metal washer is commonly used on a variety of different small engine/lawn equipment models and is sold individually. This washer is used to help evenly distribute pressure from the securing bolt or screw with the cylinder cover, to reduce any effects of vibration from the engine. If the connection between the securing fastener be...Read morecomes loose, or if you are replacing the fastener itself, it is recommended that you replace this washer as well.
This OEM Hex Socket Bolt is a black, 5x12mm, individually sold, metal part. A Hex Socket and Torque Wrench can be used to secure the part in place by torqueing to the manufacturer specifications.
The part must be replaced when damaged (likely due to fatigue), for example if it is rounded off, has stripped threads, or is missing altogether.
This is a genuine Shindaiwa part made to fit brushcutters and water pumps. Two flexible straps attach the fuel tank to the main body of the machine. There are channels which hold the straps into place, securing the fuel tank. Two metal hinges are attached to each end of the strap. This listing is for one strap.
This spark plug cap is a genuine OEM sourced replacement part that is commonly utilized on Shindaiwa lawn and garden equipment. It is used to connect the spark plug to the ignition wire. Please note this durable rubber part is sold individually.
This single-row, deep-groove ball bearing is sized at 12x32x10mm and is made of durable metal. It is used to reduce friction and vibrations when it is in between two parts that are rotating or moving against each other. This bearing can handle forces that are applied to it up-and-down and sideways, also known as radial and axial loads. It...Read more is easy to install and can handle high rotational speeds without causing too much vibration or making much noise. Over time, this ball bearing wears out from heat and pressure and starts to fail. If the engine of your machine has been run without oil in the gas tank, this ball bearing can seize. In these situations, you will need to replace the ball bearings. Otherwise, you will notice that your machine overheats, works harder because of the increased friction it is handling, and produces excessive vibration and noise. To extract a ball bearing from your machine, you will need to insert a flat-head screwdriver through the bearing opening and against the seal. Then, tap the seal out with a mallet. Afterwards, slot a socket through the diameter of the bearing, and tap the entire bearing out of its place by again using a mallet. This authentic OEM part is sold individually, so be sure to refer to your user manual to verify how many bearings your machine needs and where they are in it.
This is a genuine manufacturer sourced replacement washer that is designed for use with Shindaiwa and Echo handheld lawn and garden equipment. It helps to distribute the pressure evenly between two connected parts, for proper application please make sure to check appropriate diagrams of your unit. This part is made from durable metal and it is sold individually.
This replacement spring washer is a genuine OEM hardware that is commonly utilized on Shindaiwa and Echo lawn and garden equipment. It has multiple uses depending on the equipment, for correct location and application for this party please make sure to check appropriate diagrams for your equipment. Please note this durable metal spring washer is sold individually.
This is a genuine OEM replacement part designed to secure the blade on brush cutters/trimmers and edgers. Please note this is a hex head bolt which requires a wrench to secure it. This bolt is sold individually.
This manufacturer approved Spark Plug Terminal Cap is a part that is located inside the spark plug boot, and attaches to the spark plug to transfer the electrical current between the two. If broken, the spark plug will no longer get the electrical current it needs, and the part must be replaced. Installation is rated as "Easy" by customer...Read mores and requires pliers. This bronze, metal part is electrical and comes individually sold. Refer to your make, model and diagrams to ensure this is the correct part for you.
This is an authentic replacement part that has been sourced from the original manufacturer to be used with outdoor power equipment from Shindaiwa and Echo. The screw is used with several different types of equipment and the application of the screw can vary based on the model. This item is available as an individual replacement part, please see your model's diagram for part location and usage.