PWST Powermate Trimmer - Overview

This item is an original part from Powermate and Southland for use in cultivators. The screw knob attaches to the air filter cover. You may need a set of pliers when replacing this part. Over time this item may break or become stripped and will need to be replaced. It is made of metal and plastic and is sold individually.

This is a manufacturer authorized replacement part designed for use with cultivators. The purpose of a carburetor is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburet...Read moreor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This assembly includes a metal body carburetor with a rubber primer bulb. When replacing carburetor it is advised that you also replace carburetor gaskets to ensure proper air tight seal for optimum performance. You will need a screwdriver to perform this repair.

This is an original replacement part sourced directly from the manufacturer. The starter assembly pawl is found in cultivators from Southland and Powermate. This part is made of metal, and is used in securing the starter assembly. You may require a screwdriver and wrench when replacing this item. The starter assembly pawl is sold as an individual replacement part.

This air filter housing is designed for use with different makes and models of cultivator and is a genuine OEM part made of high-quality plastic. This part connects to the air intake for the carburetor and allows you to secure the air filter within it but does not come with the attaching air filter. Sold as an individual part, if your cur...Read morerent air filter housing is damaged, broken or does not create a good seal for the filter, it is best you replace the housing. This part does not come with the securing hardware, but is easily replaceable by removing the previous filter, disconnecting the old housing and installing the new housing and filter.

This is a genuine manufacturer-sourced replacement part which is specially designed for use with Powermate and Southland cultivators. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled eventually requiring a replacement to ensure peak performa...Read morence. This high-quality component is sold individually. You should gap your spark plug according to the owners manual of the outdoor product you have.

It is a genuine replacement component that is supplied directly from the original equipment manufacturer for use with Powermate and Southland cultivators. This gasket is utilized to create an air-tight seal between the cylinder and the isolator block, over time it may get compressed and crack eventually requiring replacement to maintain e...Read morengines top performance. It is made of high-quality composite material and it is sold individually.

This is an OEM sourced replacement part which is designed for Southland and Powermate cultivators. A centrifugal clutch connects two concentric shafts with the driving shaft nested inside the driven shaft. Keeping an eye on equipment performance will determine when the centrifugal clutch requires replacement. This high-quality clutch asse...Read morembly is made of durable metal and is sold as an individual item with included hardware. A screwdriver and a wrench will be needed to perform this repair. Refer to the appropriate diagrams for your specific model to ensure the proper replacement procedure.

This is a genuine Southland and Powermate replacement part used in compatible cultivators. The isolator block attaches to the cylinder intake gasket. During the installation process, a wrench might be needed to replace this item. It may become broken and will need to be replaced. This part is made out of plastic and is sold individually.

This fuel cap is an authentic replacement part supplied by the manufacturer. It is compatible with multiple models of Southland and Powermate lawn machinery. The purpose of this part is to prevent corrosion, protect the fuel supply, pressurize the gas tank, and seal gas tank fumes. The fuel cap should be replaced if it is cracked, does n...Read moreot click into place, or will not tighten. It is made out of plastic and requires no tools to replace.

This is available as an individual replacement part. The attachment knob attaches to the lower handle and is made of plastic. A wrench may be required to replace this item. It will need to be replaced if it becomes broken. This item is an original part from Powermate and Southland for use in blowers, cultivators, and trimmers.