Models
>
PVM9179SF3SS
PVM9179SF3SS General Electric Microwave - Overview
Sections of the PVM9179SF3SS
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Halogen Light Bulb - 120V 20W
PartSelect #: PS2351821
Manufacturer #: WB25X10019
This light bulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit before beginning th...
$22.15
In Stock
FUSE
PartSelect #: PS1481237
Manufacturer #: WB27X10928
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
$10.58
In Stock
Grease Filter
PartSelect #: PS228066
Manufacturer #: WB06X10359
Sold individually. Most microwaves require 2.
$54.19
In Stock
Glass Turntable Tray
PartSelect #: PS1016243
Manufacturer #: WB49X10176
This tray rotates in your microwave ensuring more even temperatures.
$88.85
In Stock
Halogen Lamp - 50W
PartSelect #: PS2339783
Manufacturer #: WB08X10057
Lamp also known as light bulb. Sold individually.
$21.66
In Stock
Rotating Ring
PartSelect #: PS1480805
Manufacturer #: WB06X10705
The rotating ring in your microwave rests under the microwave plate, and allows it to rotate when the microwave is running. It is a round plastic ring with 3 wheels spaced out around the perimeter. If...
$40.16
In Stock
EXHAUST ADAPTER
PartSelect #: PS12709817
Manufacturer #: WB02X32715
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs air...
$8.54
In Stock
Knob - Black
PartSelect #: PS8753661
Manufacturer #: WB03X21244
This is a control knob for your microwave. The knob is about 1.5 inches in diameter, is black and silver in color, and is sourced directly from the original manufacturer.
$40.70
In Stock
Charcoal Filter
PartSelect #: PS783520
Manufacturer #: WB02X10943
It is recommended to replace this filter yearly.
No Longer Available
Damper
PartSelect #: PS952387
Manufacturer #: WB06X10565
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out ...
$15.99
In Stock
Questions And Answers for PVM9179SF3SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the PVM9179SF3SS
[Viewing 5 of 5]Won’t turn on
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Door not closing properly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Parts Used:
-
Kim from Cliffside Park, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
953 of 1228 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Under the vent light bulbs needed to be replaced
Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!
Parts Used:
-
Robert from Naples, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
61 of 82 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loss of Rack holder clip for GE Profile Convection Microwave oven
It was super easy! Opened the door, matched up the hole on the side of the microwave convection oven with the first portion of the rack holder clip, pushed in the rack holder clip and made a twist to ensure the rack holder clip seated in the wall of the oven. Less than 30 seconds to install - no tools necessary. I that the clips came
... Read more
in an order of a unit of 8 clips, allowing me a quick-fix if I need additional clips for loss. Now I have stable racks within my oven ensuring safe insertion and removal of food from the oven. Having the full use of both of the racks in my convection oven during the summer is a Godsend, especially living in the Ohio Valley with its' hot steamy summers - my kitchen stays cool as a cucumber, and so do I!
Read less
Parts Used:
-
Nancy E from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
34 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!