This light bulb is located on the inside of your microwave. The bulb is behind the top grill. It will need to be replaced when it has burnt out and no longer works. Unplug the unit before beginning this repair. Remove the top grill of your microwave, use your screwdriver to open the light socket, scrape off any silicone holding the bulb i...Read moren place, clean the area of any oil and dirt, insert the new bulb into the socket without touching the bulb, slide the holder back into place, line up the tabs on top of the metal plate, and secure the holder back into place.
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the microwave becomes unresponsive, the microwave produces little to no heat, or the appliance simply does not turn on, it could mean that your fuse ...Read moreis at fault and needs to be replaced. Because this part contains an electrical charge, remember to disconnect power to the microwave unit before you begin this repair.
NOTE: Before you start this repair, ensure that the microwave is unplugged, and the capacitor is discharged. A capacitor stores large amounts of electricity even after your microwave is unplugged.
Maintain a cleaner kitchen environment with this multi-layer aluminum microwave grease filter. Designed to effectively trap grease particles and reduce odors, it helps prevent buildup in the recirculation system, keeping your microwave running efficiently. Ideal for replacing worn or clogged filters, this part supports a fresher cooking experience and is easy to install.
This genuine OEM halogen lamp is designed to provide bright, reliable lighting inside the microwave cavity or over the cooktop surface. Rated for high-temperature operation, it helps ensure clear visibility while cooking and venting. Replacing a burned-out or dim bulb restores proper illumination and improves everyday usability. Installat...Read moreion is straightforward once power is disconnected, and care should be taken to handle the bulb properly to ensure safe, long-lasting performance.
The rotating ring in your microwave rests under the microwave plate, and allows it to rotate when the microwave is running. It is a round plastic ring with 3 wheels spaced out around the perimeter. If your microwave plate or tray is not turning, you could have a broken or damaged rotating ring. This plastic ring is gray in color and is ap...Read moreproximately 10 inches in diameter. The 3 wheels are made of white plastic. This part is sold individually.
This is the replacement damper bracket for your microwave. It is made of plastic and is approximately 11 inches wide and 3 inches long. The damper bracket attaches to the outer cabinet and directs airflow through the vent duct. The main reason you would replace the damper bracket is if it is damaged and will not hold the damper in place p...Read moreroperly. This part is sold individually and is a genuine OEM part sourced directly from the manufacturer.
This mounting plate, also known as a bracket, is crucial for keeping your microwave mounted to the wall, when placed above the stove. This OEM part is sold separately from the screws that are needed to hold it in place. You will need a screwdriver in order to secure the mounting bracket into place. Part has been substituted. Part is no lo...Read morenger a U-shaped bracket, it is now a flat mounting plate and will function the same.
This switch monitor interlock is a critical safety component designed to ensure proper communication between the microwave door latch and the control board. When functioning correctly, it confirms that the door is securely closed before allowing the microwave to operate. A damaged or faulty switch may prevent the unit from starting, even ...Read moreif the door appears latched. Replacing this genuine part restores safe and reliable operation. Installation should be performed with care, and it's recommended to disconnect power before beginning any repair.
This vent damper is a manufacturer-approved replacement part for your above-range microwave. This part helps vent air from the microwave to the exterior of your home, and helps keep exterior wind out of the vent. Replacing the vent damper will require some disassembly of your microwave/ Unplug the unit before beginning work on it.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ken - For model number PVM1790SR1SS
June 6, 2023
Key Pad works. lights work. When I try to microwave nothing turns on. timer counts down but no power to turntable or power to microwave???
Hi Ken, thank you for writing in. Our research shows that the SWITCH MONITOR INTERLOCK part number PS11766871 and the Primary Door Interlock Switch part number PS237015 should fix your issue. This switch monitor interlock monitors the door latch position of your microwave and communicates to the electronic control board whether the latch is open or closed. If the switch is damaged, your microwave may not start, even though the door latch is closed. We hope this helps.
are the plugs and harness available that plug into the door switches. My upper switch melted the plastic plug
Hello Ken, thank you for contacting us. The compatible wire harness that plugs into the door switches is part number PS3505407. It includes the wires and the plugs. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
There is digital display, but the turntable does not turn. When the time is pressed it works, but there is no heat.
Hi Antoine,
Thank you for your question. If the turntable is not turning, you will need to check the rotating ring, the glass turntable tray, the turntable motor and the coupler. If the microwave is not producing any heat when it is on, you will need to check the line fuse, the diode, the terminal micro-switch, the magnetron, the monitor switch, the thermostat and the heater sheath. I hope this helps. Thank you and have a great day!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Craig - For model number PVM1790SR1SS
December 5, 2019
How do you replace the handle ?
Hello Craig, thank you for your question. All of our parts are pre packed from the manufacture so we can not guarantee the instructions will be in the package but, to access the door handle screws, the door choke will need to be removed. The door choke is the black plastic part around the inside of the door around the glass . It is removed by using a putty knife, carefully prying the choke cover away from the door frame. There are clips on the inside and outside of the door choke so you will have to alternate to remove both sides. Once the thre sides are removed, a Phillips head screwdriver can be used to remove the door handle screws. Hope this helps
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Troy - For model number PVM1790SR1SS
February 6, 2020
How do i change the door handle ?
Hello, Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet. You will need to remove the plastic lining around the inside of the door. There are retainer clips holding the liner in place and you will need to use a putty knife to remove it. Depending on the type of microwave you have, you may have to come in from the bottom or from the top to remove the lining. Gently slide the putty knife in between the lining and the frame and go around the frame and gently pry it loose. On the hinge side you will need to come in from the backside to pry the lining off. The door latch is held in place by tension. There is a spring that is usually attached to the latch and to one of the fins on the door to provide it. With the inner lining removed you can now remove the old latch. Install the new latch by slipping it into the slots in the door and attach the spring to the bottom fin to allow for tension in the latch. Reinstall the lining and close the door. Plug the microwave back in.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave completely stopped working
968 of 1266 peoplefound this instruction helpful.
Kim from Cliffside Park, NJ
Really Easy
15 - 30 mins
Screw drivers
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic
... Read morerowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Was this helpful?
Thank you for voting!
Under the vent light bulbs needed to be replaced
66 of 87 peoplefound this instruction helpful.
Robert from Naples, ME
Really Easy
Less than 15 mins
Screw drivers
Turned of f the circuit breaker to the microwave. Unscrewed the cover (1 screw!) popped out the old bulbs and plugged in the new ones, using the bubblewrap as a handle to be sure my skin didn't touch the light bulbs so the oil from my hands didn't damage or shorten the life of the new bulbs. Turned the circuit back on. That's it!
Was this helpful?
Thank you for voting!
Loss of Rack holder clip for GE Profile Convection Microwave oven
35 of 47 peoplefound this instruction helpful.
Nancy E from Cincinnati, OH
Really Easy
Less than 15 mins
It was super easy! Opened the door, matched up the hole on the side of the microwave convection oven with the first portion of the rack holder clip, pushed in the rack holder clip and made a twist to ensure the rack holder clip seated in the wall of the oven. Less than 30 seconds to install - no tools necessary. I that the clips came
... Read morein an order of a unit of 8 clips, allowing me a quick-fix if I need additional clips for loss. Now I have stable racks within my oven ensuring safe insertion and removal of food from the oven. Having the full use of both of the racks in my convection oven during the summer is a Godsend, especially living in the Ohio Valley with its' hot steamy summers - my kitchen stays cool as a cucumber, and so do I!
My Orders
