EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

PTW605BPR0DG General Electric Washer - Overview

Diagrams for PTW605BPR0DG

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pump Drain Assembly – Part Number: WH23X28418
$49.45
In Stock
Pump Drain Assembly
★★★★★
★★★★★
(83)
Part #WH23X28418
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram for a complete list of parts included.
MODE SHIFTER – Part Number: WH03X30517
$50.56
In Stock
MODE SHIFTER
★★★★★
★★★★★
(9)
Part #WH03X30517
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply does not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
CLUTCH – Part Number: WH05X24185
$38.31
In Stock
CLUTCH
★★★★★
★★★★★
(1)
Part #WH05X24185
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitating, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
DRIVE BELT – Part Number: WH01X24180
$27.36
In Stock
DRIVE BELT
★★★★★
★★★★★
(3)
Part #WH01X24180
This drive belt is sourced from the original manufacturer for use in various models of dryers. It is a rubber belt that connects the motor to the transmission of the washer. It enables the drum to spin and agitate during the wash cycle. The belt is prone to wear over time due to the high friction it experiences. The belt may slip, become frayed or lose tension. If the belt is faulty, the drum will have difficulty rotating, you may notice loud banging or squealing sounds, and a burning odor coming from the washer. You can find the belt near bottom of the drum or towards the back.
Water Inlet Valve Assembly – Part Number: WH13X26637
$63.64
In Stock
Water Inlet Valve Assembly
★★★★★
★★★★★
(26)
Part #WH13X26637
This is an inlet valve for models of compatible washing machines. Inlet valves are electrically controlled solenoid valves that open and close as needed during the washing cycle, to allow water into the washer. If the inlet valve has failed in your washer, you will likely see an error code or your washer simply will not start due to its failure, and it may even begin to leak water into your washer tub, and will need to be replaced immediately. This part features two valves, each with their own respective wire terminals. When replacing this inlet valve, needle-nose pliers, a socket wrench, and screwdriver will be needed, as well as some disassembly of your washing machine. This inlet valve is an OEM part that does not come sold with any other parts or accessories.
SPEED SENSOR – Part Number: WH03X32158
$39.39
In Stock
SPEED SENSOR
★★★★★
★★★★★
(13)
Part #WH03X32158
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it. If this speed sensor is damaged or bad, it will cause your washer drum to rotate too quickly, slowly, or inconsistently. Replacing this sensor will require a screwdriver and some minor disassembly of your washing machine. This sensor is an OEM part and is sold individually, so it does not come with any other parts or accessories.
SPRING CLUTCH – Part Number: WH01X24434
$16.05
In Stock
SPRING CLUTCH
Part #WH01X24434
Grinding, vibration, or poor basket movement can point to a damaged clutch spring, but other drive-system faults may cause the same symptoms. The spring helps the clutch engage during agitation and spinning. First inspect nearby pulleys, the belt, clutch surfaces, and mounting points for damage. Match the replacement to the full appliance model because similar springs may differ in length and tension. Disconnect electrical power and water before opening the washer, stabilize the cabinet, and wear eye protection when handling the spring. After reassembly, run an empty test cycle and stop if unusual noise continues.
IMPELLER/AUGER BASE – Part Number: WH43X32857
$60.26
In Stock
TRANSMISSION PULLEY & NUT – Part Number: WH03X32097
$42.81
In Stock
Anti-Siphon Clip – Part Number: WH1X2725
$15.00
In Stock
Anti-Siphon Clip
Part #WH1X2725
This part helps prevent the backflow of water from the tub to main water line.
NUT HUB – Part Number: WH02X10363
$22.91
In Stock
NUT HUB
Part #WH02X10363
DRAIN PUMP SEAL) – Part Number: WH08X24179
$16.28
In Stock
DRAIN PUMP SEAL)
★★★★★
★★★★★
(1)
Part #WH08X24179
This GE DRAIN PUMP SEAL is an essential component for your washer, ensuring a leak-free connection between the drain hose and the washer drain pump. For the assurance of a dry, well-functioning laundry setup, this reliable seal is a must-have repair item. Prior to installation, remember to disconnect power from your washer for safety. It's recommended that you wear working gloves during the installation process to guard your hands. Trust the dependable quality of GE to keep your appliance performing at its best.

Common Symptoms of the PTW605BPR0DG

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer ran fine but woudl not drain water - low humming noise
62 of 93 people found this instruction helpful.
  • Mike from NAPLES, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Drain all the water out of the tub with a shop vac
Remove rear drain hose and drained rest of water into a bucket
Remove small rear panel (bottom left hand corner) where the drain hose connects
Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans
Remove internal drain hose/clamps from pump - w/ pliers
Remove belt cover (gray plastic) with socket - 3 bolts
Remove wire assembly plug from socket
Remove old drain pump with socket - 3 bolts
Install new drain pump - 3 bolts - plug wire assembly into socket
Reinstall belt cover - 3 bolts
Reinstall hose to drain pump (note panel will be inside washer)
Feed drain hose panel through hole and reinstall - 1 nut
Re attached drain hose to exterior drain plug
You are done !
Was this helpful?
Thank you for voting!
Would not drain the water from the tub.
37 of 58 people found this instruction helpful.
  • Micheal from South Bend, IN
  • Very Easy
  • Less than 15 mins
  • Socket set
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Was this helpful?
Thank you for voting!
Water was dripping into the detergent tray when the unit was off.
28 of 37 people found this instruction helpful.
  • Richard Bibb from ARLINGTON, TX
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Removed the control panel back plate cover. Removed the 3 screws that held the water control valve in place. I then unplugged each solenoid one at a time and plugged it into the new control valve. Once all wires were transferred, I pulled the old valve up and put the new valve on. Then reinstalled the screws that held it down and reinstal led the cover plate. Very simple job !
Was this helpful?
Thank you for voting!