PS903500A Homelite Generator - Overview

This inline fuel filter is a genuine OEM part designed for use with pressure washers and generators and is sold as an individual part. Made of plastic, this filter is used to prevent dirt and debris from entering the carburetor and engine of your equipment. Regular maintenance, routine inspections, and replacement of this part will help t...Read moreo prevent any issues with your equipment in the future and ensure best performance. If your equipment is experiencing starting issues or you notice blue or dark-colored smoke coming from your equipment, the filter may need to be replaced. To replace your current filter, gain access to the fuel line or tank, restrict the flow of fuel through the filter, and simply remove it before replacing it. If your filter needs replacing, check your fuel lines for any clogs or debris build-up.

This vapor vent, also known as a vent valve or vent cap, is supplied by the original manufacturer for use with generators. It is designed to provide ventilation for the fuel tank by allowing air to enter and leave the tank as necessary. The vent prevents pressure from building up in the tank and interfering with the flow of fuel. Over tim...Read moree the vent may become clogged, or damaged leading to hard starting, fuel leakage, stalling, and the release of harmful gases into the atmosphere. It is recommended to inspect the vent before each use and replace any blocked vent promptly. To complete this repair, remove the faulty vent from the fuel tank and clean the mounting area. Thread the new vent on to the tank and ensure it is locked in place.

This fuel shut-off valve, also known as a fuel valve or fuel selector valve, is an OEM replacement part designed for use in generators. The valve controls the flow of fuel to the engine. When the valve is in the on position, fuel flows to the engine, enabling it to run. When the valve is in the off position the flow of fuel stops and the ...Read moregenerator shuts down. Over time the valve may become clogged or damaged, and unable to fully close or open. Once the fuel shut off valve is no longer functioning, the generator will leak fuel, and may have difficulty in starting or running. Before replacing the valve, first disconnect the fuel line and place a container below the fuel tank to allow the fuel to drain out. Detach the old fuel shut off valve and install the new one in its place. Apply thread sealant to the new valve for a good seal and reattach the fuel line. Refill your tank with fresh fuel and run the equipment to ensure there are no more leakages.

This is a genuine OEM sourced item that is specially designed for use with Homelite and Ryobi generators. It is an identical replacement for a missing or damaged right side isolator that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this...Read more hardware. The purpose of this component is to secure the engine to the frame and help minimize the vibrations from a working unit. Keep in mind this high-quality part is made of durable metal with rubber and is sold individually.

This authentic manufacturer-sourced part is specially designed for use with portable generators. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The part helps to secure fuel tank to the main frame, please make sure to refer to the appropriate diagrams of your model for the correct loca...Read moretion and application of this hardware. Keep in mind this high-quality isolator is made of durable rubber and is sold individually.

This is a genuine Homelite, Ridgid, and Ryobi replacement part for use in generators. The fuel cap attaches to the fuel tank. No tools should be needed during the replacement of this part. It is made out of metal and will need to be replaced if it breaks. This item is sold individually.

This is an original part from Homelite. The lock nut (m8 x 1-1/4 mm) is compatible with many pressure washers, and is sold individually. The metal lock nut helps to secure various components of the pressure washer. A wrench, hex key and screwdriver are often needed for the installation.

This replacement part is sourced directly from original equipment manufacturer. This switch is designed for use with a variety of power equipment. It is an important piece of hardware responsible for handling on/off function of equipment. Because switches have internal mechanical part, over time they will break down requiring replacement....Read more This switch has a plastic body and it includes a clear plastic cover. To complete this repair you would need a screwdriver. • First make sure the unit is not plugged in • Then you want to separate housing pieces by removing screws • Disconnect wires from the old switch • Replace old switch with a new one • Reconnect wires • Reassemble and test the unit

This is an authentic OEM part. The Homelite air cleaner gasket is made for use with several generators. The cardboard composite gasket is fitted in the carburetor assembly, preventing damage to engine parts and absorb fuel leakage. This item is sold individually. A wrench, screwdriver and a hex key are often needed for the repair.