PPRTH5A (2000) Husqvarna Tiller - Overview

This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long a...Read morend made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.

This clutch cable is designed for use with various models of tillers, and is constructed of metal, with a durable plastic insulation. The purpose of this cable is to control the primary drive function of your equipment, so when it is engaged, the tiller moves, and when it is disengaged, the tiller stays stationary. This cable is connected...Read more to a lever on the handlebar, and to a mechanism on the engine, with the cable acting as the connector. If your equipment has issues with engaging the clutch, or if the cable is frayed and damaged, the cable needs to be replaced. To replace this cable, use a screwdriver or wrench to disconnect it from the lever, before removing it from the engine mechanism. Then simply install the new one where the previous one was connected.

This genuine OEM replacement drive belt is designed for use with rotary lawn mowers and garden tillers, providing a reliable connection between the engine and the cutting or tilling mechanism. Made from high-quality, durable rubber, this belt is built to withstand regular outdoor use and is sold individually. Replacing the belt is a relat...Read moreively simple task that requires only a screwdriver. To perform the repair, first disconnect the spark plug to ensure safety. Then, remove the belt cover to access the old belt. After removing the worn belt, install the new one in its place, secure the cover, and reconnect the spark plug. Always consult your equipment’s manual for model-specific guidance and safety precautions.

This is an authentic OEM sourced replacement component which is specially produced for use with Craftsman tillers. It is the main chain that helps to drive the unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Over time the chain may wear out and stretch event...Read moreually requiring a replacement to ensure peak performance. Keep in mind this high-quality metal part is sold individually.

Measuring approximately 1-inch in length, this handle lock is designed for use with various models of tiller machines. This handle lock is fastened to the base of the handle to secure the lock lever and is a genuine OEM metal part. This part is sold individually, so depending on your model, you may need 2 of them. Be sure to check your user manual or any diagrams for confirmation.

This is an authentic manufacturer sourced replacement part that is specially designed for use with gas powered lawn and garden equipment. The purpose of this gasket is to provide an air-tight seal for the gearcase. Over time gaskets tend to get compressed and deteriorate eventually requiring replacement. Please note one durable composite material gasket is included per order.

This needle bearing is sourced from the original equipment manufacturer for use in lawn and garden equipment. It is a cylindrical roller that allows the rotating parts such as the drive shaft to move smoothly and avoid friction damage. The bearing is made from steel and designed to withstand heavy loads, and harsh outdoor conditions. Over...Read more time the bearing may wear down from lack of lubrication, or damage from the heavy loads and impacts. If the needle bearing is faulty, you will notice excessive vibration, grinding and squeaking noises, and overall lower performance from your equipment. Carefully remove the old bearing from your equipment using bearing pullers and clean the area thoroughly to ensure a good fit for the new bearing. Lubricate the new bearing and press it into position to complete your repair.

This is an original replacement part manufactured for use with garden tillers. This bearing is commonly used to reduce friction between the ground shaft assembly and the right-hand side gearcase. The special bearing is available as an individual replacement part, please see model diagram for associative parts.

t is an authentic replacement bearing that is supplied by the original equipment manufacturer for use with garden tillers. Needle bearings are used to reduce friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Symptoms of a faili...Read moreng bearing may include squealing, screeching, and an entirely new type of grinding noise. This high-quality component is made of durable metal and is sold as an individual part. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

This is a genuine manufacturer-sourced replacement component which is specially designed for use with lawn and garden equipment. It is one of the parts that helps to provide a tight seal for the shaft, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind t...Read morehis durable item is made of high-quality metal with rubber and is sold individually.

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

This is a genuine Husqvarna part for use with Tillers. The tine digs into the ground to till the soil. The most common reason for replacing the tine is if it is worn. This part is sold individually and there are no tools needed to replace this part.