PPRT55A (1997) Husqvarna Tiller - Overview

This clevis pin is an OEM replacement part that is compatible with various makes and models of tiller and is sold as an individual part. The purpose of this pin is to snap or break under a certain amount of pressure if your tiller is jammed, to protect the more valuable components of your tiller. Measuring at approximately 2-inches long a...Read morend made of high-quality metal, replacing this pin should only require pliers to swap out the old pin for the new.

This genuine OEM replacement drive belt is designed for use with rotary lawn mowers and garden tillers, providing a reliable connection between the engine and the cutting or tilling mechanism. Made from high-quality, durable rubber, this belt is built to withstand regular outdoor use and is sold individually. Replacing the belt is a relat...Read moreively simple task that requires only a screwdriver. To perform the repair, first disconnect the spark plug to ensure safety. Then, remove the belt cover to access the old belt. After removing the worn belt, install the new one in its place, secure the cover, and reconnect the spark plug. Always consult your equipment’s manual for model-specific guidance and safety precautions.

This needle bearing is sourced from the original equipment manufacturer for use in lawn and garden equipment. It is a cylindrical roller that allows the rotating parts such as the drive shaft to move smoothly and avoid friction damage. The bearing is made from steel and designed to withstand heavy loads, and harsh outdoor conditions. Over...Read more time the bearing may wear down from lack of lubrication, or damage from the heavy loads and impacts. If the needle bearing is faulty, you will notice excessive vibration, grinding and squeaking noises, and overall lower performance from your equipment. Carefully remove the old bearing from your equipment using bearing pullers and clean the area thoroughly to ensure a good fit for the new bearing. Lubricate the new bearing and press it into position to complete your repair.

This is an original replacement part manufactured for use with garden tillers. This bearing is commonly used to reduce friction between the ground shaft assembly and the right-hand side gearcase. The special bearing is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine manufacturer-sourced replacement component which is specially designed for use with lawn and garden equipment. It is one of the parts that helps to provide a tight seal for the shaft, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind t...Read morehis durable item is made of high-quality metal with rubber and is sold individually.

This is a Manufacturer Approved replacement nut for lawn and garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt.

This is a genuine Husqvarna part for use with Tillers. The tine digs into the ground to till the soil. The most common reason for replacing the tine is if it is worn. This part is sold individually and there are no tools needed to replace this part.

This is a genuine replacement part sourced from the original manufacturer for use with outdoor power equipment. The special needle bearing is commonly used to reduce friction between a rotating shaft and fixed part assembly. This needle bearing is available as an individual replacement part.

This item is available as an individual replacement part. The shifting arm attaches to the o-ring and is made of metal. A set of pliers might be required during the replacement of this part. It will need to be replaced if it becomes broken. This genuine item is supplied by the original equipment manufacturer for use with tillers, ride mowers, and cultivators made by Husqvarna, Poulan, Weed Eater, and Jonsered.

This is a genuine replacement part sourced from the original manufacturer for use with tillers made by Weedeater, Husqvarna, Jonsered and Poulan. This part goes into the ground to turn the soil. It is recommended to wear gloves to replace this left-hand tine. You will need a wrench set and socket set to replace this part. This left-hand tine is made of metal and sold individually.

This is a genuine OEM replacement part used on a variety of Lawn and Garden Equipment. This part is made out of Metal and it is Sold Individually. This steel washer has several applications based on your unit. Please refer to diagrams for proper application.

This is a genuine OEM replacement part that is used for lawn mowers and tractors across a number of brands. This is standard hardware which has multiple applications based on your tool. Please refer to diagrams for proper application. It is made out of metal and it is sold individually. You would need a wrench to remove or install this bolt.