PP336C Poulan Chainsaw - Overview

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The oil cap connects to the saw\\\'s chassis by covering the oil fill spout to prevent spills and to prevent contaminants from entering the oil tank. This item is available as an individual replacement part. Tools are not necessary to install this item.

This is an original part from Craftsman for edgers and chainsaws. This part helps turn the flying wheel when you pull on the starter rope. You may need a wrench set to replace this part. It is recommended to review your models diagram to verify the parts compatibility. This part is made of durable plastic and sold individually.

Designed for use in various chainsaws, the E-Ring secures the pivot pin, which holds the handguard. It is an authentic OEM replacement part made of durable black metal and sold individually, not as part of a kit or assembly. When this part malfunctions, you may notice the handle or handguard is loose. At which point, it will need to be ...Read morereplaced. To complete this repair, you will need a pair of pliers. Customers rate this repair as Easy.

This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap y...Read moreour spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.

This bar adjusting pin hooks onto the crankcase along with the bar adjust retainer and the screw. When you tighten the screw it helps to place tension on the bar. This high-quality pin is made out of metal and is sold individually. It is an authentic OEM sourced item which is specially produced for use with Poulan chainsaws. A screwdriver and a socket set may be needed when replacing this part.

This authentic manufacturer-sourced component is specially designed for Poulan and Husqvarna gas-powered chainsaws. It is an identical replacement for a missing or a damaged retainer that is utilized to secure the piston pin. To ensure the exact location and the correct application of this product, refer to the appropriate diagrams for yo...Read moreur specific model. Keep in mind this high-quality hardware is made of durable metal and is sold as an individual item.

This is a genuine OEM sourced replacement tapping screw which is specially designed for use with Paramount and Poulan lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams for the correct location and application of th...Read moreis part. This high-quality hex socket head screw is made of durable metal and it is sold individually.

This is a genuine manufacturer-sourced replacement part, it is specially designed for use with Poulan and Husqvarna chainsaws. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this hardware. Please note this durable metal nut is sold individually.