Models
>
PEB159CDN1BB
PEB159CDN1BB General Electric Microwave - Overview
Sections of the PEB159CDN1BB
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
FUSE
PartSelect #: PS1481237
Manufacturer #: WB27X10928
This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
$10.58
In Stock
Glass Cooking Tray
PartSelect #: PS956214
Manufacturer #: WB49X10129
There are two different couplers (also known as a turntable shaft) that can be used for this tray - a male D-shaped shaft and a female D-shaped shaft. The couplers are sold separately.
$106.23
In Stock
Oven Lamp
PartSelect #: PS247334
Manufacturer #: WB36X10131
This is a replacement oven lamp for your microwave. The base is made of black plastic, and the lamp itself is made of glass. The base is approximately 2 inches long and 1 inch wide. The bulb is locate...
$24.87
In Stock
Turntable Guide With Rollers
PartSelect #: PS223995
Manufacturer #: WB02X10719
This roller guide sits underneath the glass turntable tray.
$42.29
In Stock
Microwave Magnetron
PartSelect #: PS12722595
Manufacturer #: WB26X32629
Genuine OEM magnetron for your microwave. Always use proper safety equipment and follow the manufacturers instructions while installing.
$199.77
In Stock
THERMOSTAT
PartSelect #: PS2321365
Manufacturer #: WB21X10148
This part will trip once the inside of the cavity overheats and exceeds the recommended temperature.
$29.17
In Stock
Questions And Answers for PEB159CDN1BB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul
January 8, 2020
Hi there, as soon as I close the door on my microwave it starts humming very loudly. It does not do any normal functions any more. It was working perfectly fine and now does not work at all. What could be the problem?
For model number PEB159CDN1BB
Hello Paul, Thank you for the question. This is normally an indication one or more of the door switches are defective and will need to be replaced. They can be tested with a multi meter to check for continuity. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- Next >
Common Symptoms of the PEB159CDN1BB
[Viewing 4 of 4]No heat
Fixed by
these parts
these parts
Show All
Won’t turn on
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave completely stopped working
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Read less
Parts Used:
-
Kim from Cliffside Park, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
953 of 1228 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bulb Replacement
Remove shroud . Two black philips head screws on side, and several on the back side. The two bottom screws on the back are special screws that a philips,straight slot, or hex screwdriver will not remove. I took a dremel tool with a thin metal grinding disc and created a straight slot through the centr of the two bottom screws. This allowe
... Read more
d their removal with a straight slot screwdriver. Slide the cover straight back and off. The bulb is located on the top of the microwave connected with one screw. Replaced the bulb. It has two prongs that fit into the holder. Replace screw. Slide cover back on. It slides into retaining splines on 3 sides. Replace screws, and you're in business.
Read less
Parts Used:
-
Donald from San Marcos, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
46 of 54 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to microwave, no heating.
Unpluged power cord!! Removed front control panel to expose electronics (need to remove top horizontal vent cover to expose mounting hardware). Unplugged leads to control panel board. Removed magnetron with Tstat (3- phillip heads, need stubby). Installed new parts and control panel, plugged it in tested. Done.
Parts Used:
-
Michael from Coulterville, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
47 of 79 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!