PE-2601 (Type 1E) Echo Edger - Overview

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

Genuine Echo Replacement part, this item is sold individually. The 13031051830 Air Filter is used to keep dust and debris from contaminating the carburetor and engine. This filter is used on all the Echo Outdoor Products listed below. When this Filter gets clogged and dirty it will diminish the performance of the engine. It should be replaced at this time.

This is an OEM replacement part, it is sold individually. The Throttle Trigger controls the speed of the engine of the models listed below. The throttle cable connects to the trigger, then down to the throttle lever on the carburetor. Because of its constant use the Throttle Trigger has a tendency to break or wear out.

This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine and allows the engine to run. The spark plug comes in a cylindrical shape and is wrapped in a ceramic/porcelain insulator. It has a metal rod,...Read more known as the center electrode in the center and a metal tab at its base, known as the ground electrode. The spark plug may fail due to a buildup of carbon, physical damage, or fouling. To confirm that the spark plug is faulty, visually inspect it and use either a multimeter set to continuity or a spark tester to test the spark plug for electrical failure. Unthread the faulty spark plug using a spark plug socket and ratchet. Use a spark plug gap tool to set the correct gap and finally, carefully thread the new spark plug into the engine. Regularly inspect and replace your spark plug as part of your general maintenance to keep your equipment in good condition.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

The Cutter Blade (or Cutting blade) is a 7-3/4 inch, silver, metal blade which comes sold in a set of two. They require pliers, and a socket set to install and are rated as "Easy" to install by users. These blades are used for edging level ground sidewalks and driveways. If the part is broken or damaged due to wear from general use, they ...Read morewill become dull and will need to be sharpened or replaced. They attach to the cutting shaft. Refer to your make, model and diagrams to ensure this is the correct part.

The Cotter Pin (or Split Pin) is a 2x22mm silver metal part, sold individually. It is rated as "Easy" to install, and installation will require a set of pliers. It can be attached in various locations on a variety of equipment and is used to secure and lock parts in place. If broken, damaged, or worn down the part it is securing may becom...Read moree loose, and the part should be replaced. If this part is removed for repairs, replace it with a new one. Refer to your make, model, and diagrams to make sure this is the correct part.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This is an original manufacturer approved replacement item commonly used on trimmers, brushcutters and edgers. The purpose of this nut is to secure cutter head assembly to the spindle/shaft of a trimmer. It is a metal nut which is sold individually. Please only use properly sized wrench when securing or removing this nut.