PB-4600 (Type 1E) Echo Leaf Blower / Vacuum - Overview

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearin...Read moreg due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. ...Read moreIf the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.

Genuine OEM replacement part, this item is sold individually. The purpose of the Retainer Cushion is to isolate the vibration of the engine from the frame of the Backpack Blowers shown below. So the user does not experience excessive vibration.

This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine and allows the engine to run. The spark plug comes in a cylindrical shape and is wrapped in a ceramic/porcelain insulator. It has a metal rod,...Read more known as the center electrode in the center and a metal tab at its base, known as the ground electrode. The spark plug may fail due to a buildup of carbon, physical damage, or fouling. To confirm that the spark plug is faulty, visually inspect it and use either a multimeter set to continuity or a spark tester to test the spark plug for electrical failure. Unthread the faulty spark plug using a spark plug socket and ratchet. Use a spark plug gap tool to set the correct gap and finally, carefully thread the new spark plug into the engine. Regularly inspect and replace your spark plug as part of your general maintenance to keep your equipment in good condition.

This is an authentic Echo replacement part designed for use with backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time this part can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, at this point part should be replaced. This tube is made out of black plastic and it is sold individually.

Genuine Echo replacement part, this item is sold individually. Two of the Backpack Harnesses are needed for the Back Pack Blowers shown below. It does include the mounting hardware to attach it to the Blower. The Backpack harness is padded for comfort when using the Blower.

This is a genuine OEM replacement part used on Echo backpack blowers. Over time this part can become brittle and crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, at this point it should be replaced. This flexible tube is made out of plastic and it is sold individually.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This screw is supplied directly from original equipment manufacturer for use with Shindaiwa and Echo power equipment/tools. This screw is a standard hardware that has multiple uses depending on your model. Please make sure to check appropriate diagrams for correct location and application for this screw. It is made out of metal and it is sold individually. To secure/loosen this screw you would need a screwdriver.

This manufacturer approved replacement part is used on Echo backpack blowers. This part interlocks with the other blower tubes that are sold separately. Over time it can crack allowing for air leaks. This will greatly decrease blowing/suction ability of the unit, therefore this part should be replaced. This tube is made out of black plastic and it is sold individually

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This heavy duty air filter is made out of pleated paper and it is sold individually. It is commonly used item on a variety of backpack gas powered blowers. It is designed to filter our dust and debris which could enter carburetor and engine. It is recommended to periodically check on condition of your air filter. Over time it will get clo...Read moregged preventing air from entering carburetor. This will greatly affect blowers performance, at this point filter should be replaced. Replacing this air filter is easy and does not require any tools. • First remove the air filter cover by releasing tabs • Remove old air filter • Clean out the filter base from any left over dust • Place new air filter in the case • Reassemble and test the blower