PAS-2400 (Type 1E) Echo Chainsaw - Overview

This is a genuine ECHO/Shindaiwa replacement part It is compatible with over 150 machines listed below. The Fuel Line Grommet is placed into the fuel tank. The Vent tube, Fuel return line and fuel line are inserted through the three holes. A worn Fuel Line Grommet will cause fuel to leak from the tank. When replacing the Grommet it is advisable to replace the fuel lines at the the same time.

This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for ...Read morerecommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs on...Read moreto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

The fuel return tube or fuel return line, as it is also known, delivers fuel back to the tank from the primer bulb. This is a genuine OEM part from the manufacturer, and it is yellow in color and sold individually. Its overall dimensions are 3x6x90mm. Over time, or due to over-tightening, cracks may appear in your fuel return tube, causin...Read moreg fuel to leak. You will know it is time to replace this part if you notice these symptoms. This is an easy repair, according to our customers, and does not require any special tools. The new part will simply attach to the primer bulb and fuel tank.

This is the replacement vent tube for your outdoor power equipment. It is made of black plastic and is approximately 3 inches long and ¼ inch thick. The vent tube allows air into the fuel tank so that a vacuum is not created when fuel is being fed through the fuel line. The vent tube is often connected to the fuel line grommet that is ins...Read moretalled on the fuel tank. If the vent tube is broken or missing, it can lead to decreased engine power and performance. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.

Genuine Echo Replacement part, this item is sold individually. The 13031051830 Air Filter is used to keep dust and debris from contaminating the carburetor and engine. This filter is used on all the Echo Outdoor Products listed below. When this Filter gets clogged and dirty it will diminish the performance of the engine. It should be replaced at this time.

This is an OEM replacement part, it is sold individually. The Throttle Trigger controls the speed of the engine of the models listed below. The throttle cable connects to the trigger, then down to the throttle lever on the carburetor. Because of its constant use the Throttle Trigger has a tendency to break or wear out.

This is a genuine manufacturer approved replacement part designed for use with edgers and trimmers. The purpose of this part is to act as a seal for the insulator. This item is made out of compound material and it is sold individually. To complete this repair you would need a screwdriver.

This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine and allows the engine to run. The spark plug comes in a cylindrical shape and is wrapped in a ceramic/porcelain insulator. It has a metal rod,...Read more known as the center electrode in the center and a metal tab at its base, known as the ground electrode. The spark plug may fail due to a buildup of carbon, physical damage, or fouling. To confirm that the spark plug is faulty, visually inspect it and use either a multimeter set to continuity or a spark tester to test the spark plug for electrical failure. Unthread the faulty spark plug using a spark plug socket and ratchet. Use a spark plug gap tool to set the correct gap and finally, carefully thread the new spark plug into the engine. Regularly inspect and replace your spark plug as part of your general maintenance to keep your equipment in good condition.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

This is a genuine OEM replacement part, this item is sold individually. The Corrugated Fuel Tube is situated inside the fuel tank. The fuel filter is connect to it. It also connected to the fuel line by means of the fuel grommet on the fuel tank. It part of the delivery system that supplies fuel into the carburetor.

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.