PAS-230 (S67711001224-S67711001252) Echo Trimmer - Overview

This Genuine OEM air filter is a critical component designed to protect your engine by preventing dirt, dust, and other small particles from entering the carburetor and causing internal damage. Sold individually, this high-quality filter features a double-layer construction that enhances filtration efficiency and ensures optimal airflow. ...Read moreOver time, filters can become clogged with debris, restricting air intake and reducing engine performance. For best results, this type of filter should be replaced—not cleaned—once it becomes dirty. Regular replacement helps maintain engine health and ensures reliable operation of your outdoor power equipment.

This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to install. It is attached inside of the cylinder head, and is used to ignite the air fuel mixture inside the combustion chamber. You can clean...Read more the spark plug with a fine sandpaper of 180 or more, then spray it with carburator cleaner and wipe dry. However, even after regular maintenance, spark plugs need to be changed as part of good engine fine-tuning. Regap to manufacturer specifications. Refer to your owners manual or model number to ensure you are choosing the correct product. Note: If your engine has more than one cylinder and sounds like it has a miss, you can remove each spark plug wire one at a time to find the miss. If the engine drops in rpm when you remove the wire, then that cylinder is fine, if it does not drop then you have found your miss!

This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.

This is an OEM replacement part, it is sold individually. The Throttle Trigger controls the speed of the engine of the models listed below. The throttle cable connects to the trigger, then down to the throttle lever on the carburetor. Because of its constant use the Throttle Trigger has a tendency to break or wear out.

The Wing Bolt is a gold, metal bolt, sold individually. It is rated as "Easy" to install, and requires no special tools. This part secures the air filter cover and air filter to the air cleaner case, and attaches to the air cleaner assembly. If broken due to fatigue/wear/damage, the air cleaner assembly will come loose. Refer to your make, model and diagram to ensure you're choosing the right part for your assembly.

Genuine OEM replacement part, this item is sold individually. The purpose of the part is to cover the air filter on the outdoor products shown below. It helps keeping larger pieces of debris from coming in contact with the air filter. While providing enough clearance for air to enter the carburetor through the air filter and mixing with the fuel to make the unit run properly.

Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove th...Read moree screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.

Genuine OEM replacement part, this item is sold individually. The purpose of the part is to cover the air filter on the outdoor products shown below. It helps keeping larger pieces of debris from coming in contact with the air filter. While providing enough clearance for air to enter the carburetor through the air filter and mixing with the fuel to make the unit run properly.

Genuine Echo replacement part, this item is sold individually. This is part of the safety start system on all of the trimmers listed below. This part is installed on the top handle and has to be pressed down while pulling the starter rope in order for the engine to start.

Used in over 150 models of outdoor power equipment, this clip is commonly used to clip fuel lines or other hoses/tubes in place. It is sold individually, not as part of a kit or assembly, made of metal, and is silver in color. When this clip becomes damaged or worn, it can no longer support the fuel line, which may cause a fuel leak and...Read more/or smell. This wear will occur as part of regular use of your equipment. To complete this repair, you will need a wrench, screwdriver, and pliers. It is found in a variety of locations depending on your model; please refer to your owners manual for the exact location. Customers rated this repair as Easy.

This piston ring is an authentic manufacturer approved replacement part. Is is commonly used on Echo gas trimmers/edgers. The purpose of a piston ring is to create an air tight seal inside the cylinder. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and...Read more a loss of power. Replacing an o-ring should resolve this issue. This part is made out of metal and is sold individually. To complete this repair you will need a set of wrenches, pliers and a screwdriver. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring • Reassemble and test the equipment