Trash compactor bags are a practical way to discard your waste. Due to the extreme pressure of the compactor, trash compactor bags designed to handle the force are necessary. These bags are made from tough 2.5-millimeter, multi-laminate plastic, and the patented Slip-Grip design prevents the bag from slipping into the compactor bin. They ...Read moremeasure approximately 15 inches wide x 15 inches high and are made from 50 percent post-consumer recycled plastic. This pack of 15 trash compactor bags is a genuine OEM replacement part, and will fit most rectangular 15-inch trash compactors.
The rotary switch kit is also known as the start switch or the on and off switch, and is used to power on your trash compactor. The function of the rotary switch kit is to control the electrical power that is going into your trash compactor. This process happens when the switch sendsvoltage to the motor to start the compacting cycle. If y...Read moreour switch is broken the trash compactor will not start. A multimeter test can be performed to test the switch for continuity. The rotary switch kit will come with an on and off rotary switch, and two chrome knobs.
This is a 60-pack of plastic compactor bags. These bags are 15 inches wide, 3 millimeters thick and are white in color. The 3-millimeter thickness makes the bags more durable and helps prevent tearing. They are an environmentally-conscious product that are made of 50% post-consumer recycled material. The bags feature a Slip-N-Grip design ...Read morethat prevents the bag from slipping down into the compactor. Strong resin that is incorporated into the material increases puncture and tear resistance to help keep your trash in the bag. These bags will fit 15-inch rectangular compactors.
This replacement part is a foot pedal which fits on a trash compactor. It includes two screws for installation. The pedal mounts on the footplate on the bottom front of the container. The pedal controls the container drawer. When stepping on your trash compactor pedal, the latch should release the container from the compactor body. This f...Read moreoot pedal is black, made of plastic, and is sold individually. Be sure to disconnect power to your appliance before beginning this repair. You will only need a screwdriver to complete the repair. This is a genuine part and is sourced from the authentic manufacturer.
This wheel assembly, or roller assembly, is for a trash compactor. The kit includes two wheels that are approximately 1 inch in diameter each. The wheels allow the trash compactor container to roll in and out of the appliance. You may have to replace the wheel assembly if the container does not roll smoothly. To access the existing wheel ...Read morekit on your appliance, uninstall appliance from the cabinet, depress foot petal to lift the container off its track, and remove the container from the tracks. This kit is an OEM part sourced from the authentic manufacturer factory.
This replacement knob and safety key is designed for trash compactors, providing both convenient operation and added protection. It functions as the start control, allowing you to easily activate the compactor, while also serving as a built-in safety feature—removing the key disables the unit to help prevent unintended use. Durable and ea...Read moresy to install, it’s an ideal solution for replacing worn, damaged, or missing knobs, helping restore safe and reliable everyday operation.
The light switch terminal is used in refrigerators and freezers to allow you to see inside your appliance by turning on when the fridge door is open and turning off when the door is closed. This part is 1.12 inches in length, 1 inches in width, and 1.75 inches in height. It weighs 0.026 pounds. If your light switch terminal is damaged or ...Read morethe light does not turn on when fridge door is open, replacing the light switch terminal can fix the problem. As a safety precaution, remember to unplug your fridge from the power source before beginning this installation. Refer to the manual provided by the manufacturer for further installation instructions and a detailed guide.
This drive motor is for trash compactors. The drive motor turns the gears and chain that raise and lower the compactor ram. If your trash compactor will not start or will not stay on during the compaction cycle, you may have a defective drive motor. The start or run switch is used to supply power to the motor to initiate the compaction cy...Read morecle. If the windings in the motor are open or if the motor centrifugal switch is open, the unit will not start. To check for a defective motor, you will need to remove the unit from the cabinets and disconnect the power.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Old Plastic Compactor Key Became Brittle and Broke
32 of 37 peoplefound this instruction helpful.
Ron from El Paso, TX
Really Easy
Less than 15 mins
Pliers
Original key part number was 776586 as found underneath the the rim of the broken key. It's known as a compactor key, or a key-knob, but in layman's terms, I would call it the "off-on-start" knob. The replacement part number was 386676, and fits perfectly. The original key had become old and brittle, and eventually just broke a
... Read morepart. This was a 30+ year old Whirlpool Trash Compactor key. I just picked out the bits of the old broken key with needle-nose pliers and then easily inserted the new key into the opening. Note, this literally works just like a key you would insert into any lock. It doesn't require pushing to "snap" into place, but once inserted and turned to the "ON" position, locks into place. No forcing is required at all. The new key looks exactly like the original and is working very smoothly.
Read less
Was this helpful?
Thank you for voting!
Trash compactor would not start
21 of 27 peoplefound this instruction helpful.
Ryan from Delta, CO
Easy
Less than 15 mins
Screw drivers
Remove two screws from panel above trash bin. Remove panel and remove wires from rotary switch. Remove lock ring from switch. Install in reverse order.
Was this helpful?
Thank you for voting!
To replace old pedal where screw hole was stripped
12 of 15 peoplefound this instruction helpful.
Preston from Memphis, TN
Easy
15 - 30 mins
Screw drivers
Had to remove entire drawer from unit to more easily access pedal placement. Removed old pedal. Screwed new pedal in place. Replaced drawer unit. Done.