P-WLE-1639-E Powermate Edger - Overview

It is a genuine manufacturer-supplied item that is made for use with Powermate, Southland and Airstream lawn edgers. This item provides an identical replacement for a damaged or a missing drive shaft assembly that was installed on a new unit. Check the owner's manual and the diagrams for your model to ensure the correct repair procedure. ...Read moreNote, this high-quality assembly is made of durable metal and is sold individually. A wrench set and pliers might be needed when replacing this component.

This drive shaft is designed to transfer power smoothly and reliably within lawn edgers, supporting clean, consistent edging performance. Made from durable metal, it helps maintain proper operation when replacing a worn, bent, or damaged shaft. Ideal for routine repair or maintenance, it restores dependable power delivery and overall tool performance in 4-cycle edging equipment.

This genuine OEM fuel line fitting or filter in your lawn equipment ensures clean fuel flow from the tank to the engine in your lawn equipment. It effectively removes debris and impurities, safeguarding the engine from potential damage. Typically located along the fuel line, it is close to the fuel tank or engine. You can tell if it is br...Read moreoken or clogged if there are signs of fuel leakage, reduced fuel flow, or if the engine fails to start or run smoothly. If the fuel line fitting or filter is not replaced, it can lead to poor engine performance, fuel starvation, and potential damage to the engine components. To remove it, you will need a screwdriver, pliers, and a socket set. Disconnect the fuel hose from the carburetor, drain the tank, and unbolt the fuel tank. Then, detach the fuel line and use a socket to remove the fitting. Remember, this replacement part is sold separately from the rest of the fuel line assembly.

This authentic OEM air cleaner element, also known as an air filter, includes one paper filter surrounded by a foam pre-cleaner for use in a variety of outdoor power equipment. The foam pre-cleaner acts as the first protective barrier and traps larger particles to prevent them from clogging or tearing the paper filter. However, it is norm...Read moreal for the air filter to become clogged or torn due over time, due to accumulated dirt and debris, or due to prolonged use without replacement. A faulty air cleaner will result in poor engine performance, rough idling, hard starting, stalling, and increased fuel consumption. It is recommended to replace your air filter every 3-6 months for optimal performance. You can find the air cleaner housing near the carburetor or air intake on your equipment. Detach the housing cover and remove the faulty filter. Clean the housing and place the new air cleaner in position. Reattach the air cleaner cover to complete your repair.

This fuel tank cap is an authentic OEM replacement part sourced directly from manufacturers such as Powermate, Homelite, Southland, and Airstream. It is made for use with multiple models of lawn edgers. This fuel tank cap is made of plastic and sold individually. This cap prevents outside contaminants from entering the tank. It should be ...Read morereplaced if it is damaged or will no longer tighten. NOTE: This cap only fits the older version of the tank, part number A100783. It dose NOT fit the newer tank, part number A202711. Part number A202712 fuel cap will fit this newer tank.

This control rod is designed for use with various models of edgers and is a genuine OEM part sold without any securing hardware such as bolts or pins. By moving the rod, you can raise or lower the level at which the edger cuts, which is important when different soils require different cutting depths. If you notice that the control rod is ...Read morehard to move, inspect it for rust, corrosion, bends, or general damage, at which point it will likely need to be replaced. To prevent having to replace this control rod more frequently, make sure to adequately lubricate any connected parts attached to the rod, as well as generally keep the part(s) clean. To replace the control rod on your edger, you will need a wrench and pliers to disconnect the bolts and hair pins securing the rod to their control handle. At this point you can remove the old rod and install the new one, and the rest of the depth controlling assembly.

This high quality OEM supplied replacement part is designed for use with gas powered lawn and garden equipment. By pressing on the primer bulb, it will force fuel into the line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess will be purged back into the tank through the return line. At some time the...Read more primer may lose its elasticity or crack eventually requiring replacement. One durable plastic item is included per order.

This part is an OEM from the Powermate manufacturer. The metal index lever is compatible with several edger devices, and is fitted onto the drive shaft assembly. The index lever sets the blade angle. This item is sold individually. A wrench may be helpful in the repair.

This torsion spring is designed for use with various makes and models of edger and is sold as an individual part. Located near the blade, this spring is used to apply resistance on the blade for when the blade is cutting against various outdoor surfaces to maintain a straight edge. This spring is made of metal and will require a screwdriv...Read moreer and wrench to replace. For the exact location of your edger torsion spring, refer to any user manuals or diagrams.

This is a genuine Powermate replacement part sourced directly from the manufacturer. The nut is generally found in lawn edgers. This is a metal part that is used to secure the ends of the drive shaft and hold it to the blade arm. Please be aware that there are different nuts used in the machine. Refer to the parts diagram to be sure o...Read moref ordering the correct part. You will require a wrench when replacing this part. This item is sold individually.

In your edger, this nut attaches the cutting blade to the drive shaft assembly. Having a 12-millimeter diameter and a thread pitch of 1.25mm, it secures the blade so that you can effectively cut through grass, weeds, or other vegetation. A broken nut becomes loose during operation, disengaging the cutting blade. You may also notice that i...Read moret is cracked, fractured, or its threads have been stripped. If a damaged nut is not replaced, you will experience uneven trimming. This also poses a safety concern as injuries may happen if the blade detaches during operation. To remove this nut from your machine, you need to immobilize the blade using a blade lock so it does not rotate. Using a wrench or a socket, loosen the nut by turning it counterclockwise. You can then continue to unscrew it by hand before removing it from the blade completely. Before adding this OEM replacement part to your cart, please keep in mind that this nut is sold individually and separately from the cutting blade.