P-WB-163150 Powermate Leaf Blower / Vacuum - Overview

This genuine OEM fuel line fitting or filter in your lawn equipment ensures clean fuel flow from the tank to the engine in your lawn equipment. It effectively removes debris and impurities, safeguarding the engine from potential damage. Typically located along the fuel line, it is close to the fuel tank or engine. You can tell if it is br...Read moreoken or clogged if there are signs of fuel leakage, reduced fuel flow, or if the engine fails to start or run smoothly. If the fuel line fitting or filter is not replaced, it can lead to poor engine performance, fuel starvation, and potential damage to the engine components. To remove it, you will need a screwdriver, pliers, and a socket set. Disconnect the fuel hose from the carburetor, drain the tank, and unbolt the fuel tank. Then, detach the fuel line and use a socket to remove the fitting. Remember, this replacement part is sold separately from the rest of the fuel line assembly.

This OEM capped clip is designed to securely fasten the rear wheel of your walk-behind blower, ensuring it stays in place during operation. If the clip is worn out or broken, the wheel may become loose or wobbly despite attempts to tighten it. If left unreplaced, there is a risk of the rear wheel becoming detached or dislodged. To remove ...Read morethe capped clip, locate it on the wheel axle and use pliers to squeeze the ends together, releasing the tension and allowing you to slide the clip off the axle. Before purchasing this replacement part, verify how many your machine will need as it is sold individually.

This authentic OEM air cleaner element, also known as an air filter, includes one paper filter surrounded by a foam pre-cleaner for use in a variety of outdoor power equipment. The foam pre-cleaner acts as the first protective barrier and traps larger particles to prevent them from clogging or tearing the paper filter. However, it is norm...Read moreal for the air filter to become clogged or torn due over time, due to accumulated dirt and debris, or due to prolonged use without replacement. A faulty air cleaner will result in poor engine performance, rough idling, hard starting, stalling, and increased fuel consumption. It is recommended to replace your air filter every 3-6 months for optimal performance. You can find the air cleaner housing near the carburetor or air intake on your equipment. Detach the housing cover and remove the faulty filter. Clean the housing and place the new air cleaner in position. Reattach the air cleaner cover to complete your repair.

This OEM ball bearing plays a crucial role in supporting and enabling the rotation of the wheel in walk-behind blowers. It is a metal ring housed within a protective casing that enables the well to spin freely while supporting the weight of the blower. Over time the bearing may wear down, due to age, corrosion, or inadequate lubrication. ...Read moreIf the bearing is faulty, you will notice increased resistance when moving your equipment, excessive noise, and wheel instability. To remove and replace the wheel bearing, first, disassemble the wheel assembly to access the bearing. Remove the old bearing by carefully prying it off using a bearing puller. Clean the wheel hub thoroughly and apply a small amount of lubrication to the new bearing. Press the bearing onto the wheel and secure it with the appropriate fasteners. Reassemble the wheel assembly and give the blower a test run to ensure the wheel can rotate freely.

This fuel tank cap is an authentic OEM replacement part sourced directly from manufacturers such as Powermate, Homelite, Southland, and Airstream. It is made for use with multiple models of lawn edgers. This fuel tank cap is made of plastic and sold individually. This cap prevents outside contaminants from entering the tank. It should be ...Read morereplaced if it is damaged or will no longer tighten. NOTE: This cap only fits the older version of the tank, part number A100783. It dose NOT fit the newer tank, part number A202711. Part number A202712 fuel cap will fit this newer tank.

This is an authentic Southland replacement part. The flat washer is found in a walk-behind blower. This part is made of metal, and is used to help secure the wheel onto the machine. Please be aware that there are different washers used in the machine. Refer to the parts diagram to be sure of ordering the correct part. This item is sold individually.

This high quality OEM supplied replacement part is designed for use with gas powered lawn and garden equipment. By pressing on the primer bulb, it will force fuel into the line from the fuel tank into the carburetor. Once the carburetor is full of fuel, the excess will be purged back into the tank through the return line. At some time the...Read more primer may lose its elasticity or crack eventually requiring replacement. One durable plastic item is included per order.

The carburetor is made of metal and is available as an individual replacement part. When replacing this part a set of pliers, a socket set, and a wrench set may be needed during the installation process. This item may stop working and will need to be replaced. It is a Southland replacement part directly sourced from the manufacturer for use in cyclone walk behind blowers.

This is an OEM replacement part for Southland cyclone walk behind mowers. The wheels allow you to easily move your lawn mower from place to place. This part is made out of plastic and rubber and it is also sold individually, though four are required for the unit. Before installation, make sure the engine has cooled, and disconnect the wir...Read moree and boot from the spark plug. For installation, you will need a socket wrench, and a screwdriver to aid you.

This is available as an individual replacement part. The attachment knob attaches to the lower handle and is made of plastic. A wrench may be required to replace this item. It will need to be replaced if it becomes broken. This item is an original part from Powermate and Southland for use in blowers, cultivators, and trimmers.

This spark plug is used in small gas-powered equipment to ignite the air-fuel mixture for reliable starting and smooth engine operation. It’s a direct replacement for worn or fouled plugs and helps restore proper ignition, consistent performance, and efficient running during routine maintenance or engine service.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with walk-behind lawn edgers. The gasket is used to seal the connection between the carburetor and the heat insulator. This item is available as an individual replacement part.