Models
>
NX58F5500SBAA
NX58F5500SBAA Samsung Microwave Oven Combo - Overview
Sections of the NX58F5500SBAA
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Range Oven Temperature Sensor
PartSelect #: PS4240743
Manufacturer #: DG32-00002B
This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will ...
$130.08
In Stock
Oven Burner Igniter
PartSelect #: PS4241428
Manufacturer #: DG94-00520A
This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent...
$218.00
In Stock
Rubber Cushion
PartSelect #: PS4241222
Manufacturer #: DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It preven...
$6.59
In Stock
Range Oven Door Switch
PartSelect #: PS4240750
Manufacturer #: DG34-00006A
The oven door switch shuts the oven light off when you close the oven door.
$67.21
In Stock
Questions And Answers for NX58F5500SBAA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the NX58F5500SBAA
[Viewing 3 of 3]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating and holding temp
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the c
... Read more
enter of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
Read less
Parts Used:
-
John from EAST QUOGUE, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not heat consistently
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the
... Read more
issue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!
Read less
Parts Used:
-
Steven from CHEYENNE, WY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven igniter burned out
Took out oven racks and bottom steel plates, unscrewed old igniter and replaced with new one, only problem was plastic connections were different so I needed to strip wires and use wire nuts. Very easy fix that anyone could do..
Parts Used:
-
Wayne from PLEASANT VLY, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!