Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This basket drive hub kit is a vital component in select washing machines, designed to connect the wash basket to the central drive shaft, enabling proper rotation during wash and spin cycles. It play...
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This is a lid strike for various models of top-load washing machines. Lid strikes are designed to engage with the lid switch and communicate to the control board that the washer can start. If your was...
This is a shift actuator, and is designed for use in washing machines. This shift actuator is made to change the mode of the motor between spin and agitate, as well as communicate with the control boa...
This is an inlet valve for various washing machines. Inlet valves are responsible for opening and closing as needed, to allow water to enter the washer during the washing cycle. This inlet valve featu...
This agitator is for washers.
Agitator rotates back and forth to move the clothes inside the tub to clean the load.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
$78.38
In Stock
Order now and your part arrives by May 28
Questions And Answers for NTW4519JW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
34 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
June 13, 2024
After load complete light comes on and the red light to unlock it keeps running like humming if I turn the load a quarter turn it stops then humming again I have to unplug it
Please can you tell me why and the washer is level thank you please help it's not in the trouble shooting section
For model number NTW4519JW2
Hi Ed, thank you for contacting us. It appears that your washer may have a damaged control board, part number PS16744865, and you may need to replace it to fix the issue. Glad to be of assistance!
Why is my washer using hot water when it’s set to cold? I even tried “tap cold” option and still running hot.
For model number NTW4519JW2
Hi Roberta, thank you for the question. The water supply lines could be connected incorrectly behind the machine. You will need to disconnect the supply lines, run water into a bucket to confirm both hot and cold, then reconnect them to the appropriate connection behind the machine. If this is not the issue, we would recommend checking the water temperature selector switch, part number PS11731444. Good luck with this repair!
2 people found this helpful.
Did this question help you?
Thank you for voting!
Keith
February 5, 2025
water will not shut off with a small load of clothes.
For model number NTW4519JW2
Hello Keith, Thank you for writing. If the washer will not stop filling with water, the most likely culprit is a faulty water pressure switch. The Pressure Switch for this model is part of the Control Board. We hope this solves your problem!
After cycle is done and spinning complete the washer has a buzzing sound like it is turned on even tho load is done. I have it unplugged now because nothing changes this!
Washer is 1 1/2 yrs old.
For model number NTW4519JW2
Hello Gloria, thank you for reaching out. Based on the description that you have provided, it’s likely that a component such as the drain pump or inlet valve is stuck in the “on” position due to a relay issue on the control board. Sometimes, the control board can fail to signal these components to turn off, causing the buzzing sound even when the cycle is finished. Inspect the control board for any signs of burning or damage; if found, the board should be replaced to resolve the issue. The part number is PS16744865. We hope this information helps!
washes fine an when done sounds like water pump start running for no reason an have to unplug
For model number NTW4519JW2
Hi Dean, thank you for getting in touch. According to our research, the issue could be because of the water pressure switch or the water level sensor. When this sensor fails, it cannot detect that the water has already drained, causing the pump to run indefinitely as a safety measure. The pressure switch for your model is integrated into the main control board, part number PS16744865, and replacing it might fix the issue. We hope this solves your problem!
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install
... Read more and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
