This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a specific internal temperature. In some cases, high limit thermostats can become defective and if your appliance will not turn on, or has a spe...Read morecific error code, it must be replaced. This thermostat is a genuine OEM part that is sold as an individual part and can be replaced by disconnecting the appliance from the power, and accessing its panel, usually located near the bottom of your range, or wherever the heating element is located. Reference your user manual for exact location and replacement instructions.
This convection fan motor assembly is designed to circulate hot air throughout the oven cavity, promoting even heat distribution for more consistent baking and roasting results. By keeping air moving during convection cooking, it helps eliminate hot spots and improves overall cooking performance. Replacement is often needed if the oven fa...Read moren becomes loud, stops spinning, or causes uneven cooking temperatures. Supplied as a complete motor and fan assembly, this component offers a reliable solution for restoring quiet operation and efficient convection airflow when the original fan motor is worn or damaged.
This surface element triple burner infinite switch, or regulator control, is located in the control panel of your range oven. It is responsible for turning the surface element on or off and adjusting its heat. If this switch or regulator is broken, you might notice the burner heating uncontrollably or not heating at all. Please remember t...Read morehat genuine OEM replacement part is designed for triple burners. Your range model may use various types of switches, so be sure to choose the correct one when making your purchase.
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.
This energy regulator, more commonly known as a surface element control switch or burner switch is compatible with various models of Samsung ranges. It consists of the switch housing and a metal shaft. The burner switch is responsible for turning the surface element on and off and controlling the amount of heat that is produced by the sur...Read moreface heating elements on the stove. The most common sign that your element control switch is faulty is if the burner will only turn on high heat. Other signs of failure include difficulty adjusting the control knob, failure to produce heat, and the burner not shutting off.
This stainless steel wire rack is a sturdy platform for baking or roasting food, making sure heat circulates evenly. It measures approximately 7/16 inches by 24 3/4 inches and is usually found inside the oven. You can adjust its height using the multiple slots in the oven cavity to suit your cooking needs. Please keep in mind that this genuine OEM replacement part is sold individually.
This display board is for ranges.
Display board receives signals from the control board and displays the time and temperature settings.
Unplug the range or shut off the circuit breaker before installing this part. Wear work gloves to protect your hands.
This terminal block assembly is designed for use within various models of ranges and is sold as an individual OEM part without any other hardware included. Terminal blocks are responsible for receiving, managing, and distributing the power within an appliance. Electrical shorts or surges can cause this terminal block to overheat and melt ...Read moreand become inoperable, thus needing immediate replacement. If you smell melting plastic when operating your range, turn it off and disconnect it from power immediately and inspect this terminal block and all other electrical components. To replace this terminal block, disconnect your range from the power and remove it from the wall. Remove the back panel of the range and locate the terminal block, making note of its wire configuration. Unscrew the wires and the ground wire if there is one, and then do the same for the mounting screws. Install the new terminal block in the same position as the previous one, attaching all necessary wires as they were originally, before you reconnect and reposition the range.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The triple burner switch would only stay on the highest setting.
17 of 18 peoplefound this instruction helpful.
Jimmie D. from THOMPSON, MO
Really Easy
30 - 60 mins
Screw drivers
I removed the control panel with a Phillips screwdriver and unplugged the burner switch and replaced the new switch and put the control panel back in place and turned on the burner and it worked as it should.i realized that I only would have only had to remove the 4 screws on the bottom of the control panel. All I would have had to do was
... Read more just take those 4 screws out and remove the switch control knob and the two screws that held the switch in. Am very happy with the results
Read less
Was this helpful?
Thank you for voting!
When I turned on triple burner on any of the three burners it would immediately go to high mode
9 of 9 peoplefound this instruction helpful.
David from NAVARRE, FL
Really Easy
30 - 60 mins
Screw drivers
Cool oven, open door. Turn off electrical power. I laid a cloth over door to protect and to catch ant screws that my fat fingers would drop. I removed 4 screws under control panel. I pulled panel up and off stove face. My wife held it safely as I removed the triple burner knob. I then placed new switch, on stove top in same position as ol
... Read mored one. I then removed screws holding old knob to release from control panel. The removed electrical connections one at a time and installed on new switch. Reinstalled switch back in control panel. Reinstalled control panel. Placed knob back in place. Turned electrical power back on. Then tested burner. Wife is happy and so am I.
Read less
Was this helpful?
Thank you for voting!
Oven shut off during self clean cycle and door stayed locked.
23 of 51 peoplefound this instruction helpful.
Uwe from FORT COLLINS, CO
Very Easy
15 - 30 mins
Screw drivers
I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.