Models > NDU5CA-01

NDU5CA-01 Norge Dishwasher - Overview

Sections of the NDU5CA-01

[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Screw - 6-32 x 5/16 – Part Number: WP74004005
Screw - 6-32 x 5/16
PartSelect #: PS11744050
Manufacturer #: WP74004005
This screw is well under an inch long, and is made of metal.
$5.36
  Special Order
WHEEL – Part Number: W10542232
WHEEL
PartSelect #: PS5573993
Manufacturer #: W10542232
  No Longer Available
Clamp – Part Number: WP696392
Clamp
PartSelect #: PS11743796
Manufacturer #: WP696392
This screw-type clamp, also known as a hose clamp, is made of metal and is used within various models of washers to secure the tub-to-pump hose and tub/drum of the washer. Without this clamp, the hose...
$9.00
  In Stock
SCREW – Part Number: 61002031
SCREW
PartSelect #: PS2057900
Manufacturer #: 61002031
Sold Individually.
$30.69
  Special Order
Lower Front Wheel – Part Number: WP2955-0007
Lower Front Wheel
PartSelect #: PS11740619
Manufacturer #: WP2955-0007
  No Longer Available
Door Gasket – Part Number: 2450-0025
Door Gasket
PartSelect #: PS2026248
Manufacturer #: 2450-0025
  No Longer Available
DISCONTINUED – Part Number: Y03000185
DISCONTINUED
PartSelect #: PS2191527
Manufacturer #: Y03000185
  No Longer Available
SPRAY ARM – Part Number: Y03000107
SPRAY ARM
PartSelect #: PS2191502
Manufacturer #: Y03000107
  No Longer Available
DISCONTINUED – Part Number: 2905-0009
DISCONTINUED
PartSelect #: PS2028343
Manufacturer #: 2905-0009
  No Longer Available
DISCONTINUED – Part Number: Y03000003
DISCONTINUED
PartSelect #: PS2191478
Manufacturer #: Y03000003
  No Longer Available
SCREW – Part Number: 910187
SCREW
PartSelect #: PS2097465
Manufacturer #: 910187
$7.49
  Special Order
SEAL-PUMP – Part Number: R0913111
SEAL-PUMP
PartSelect #: PS2173291
Manufacturer #: R0913111
  No Longer Available

Questions And Answers for NDU5CA-01

Be the first to ask our experts a question about this model!

Common Symptoms of the NDU5CA-01

[Viewing 1 of 1]
Leaking
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wouldn"T Drain The Water Completey
Removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. . . )
Parts Used:
MOTOR-PUMP
  • clarence from ST LOUIS, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Two upper rack rollers were broken
Used ascrewdriver to bend the metal rail that the roller rolls on. The part that needed to be bent holds the end cap on. Once bent, the end cap pops off. The the old roller can be removed and the new roller instsalled. The rail then needs to be re-bent.
Parts Used:
WHEEL
  • Duane from Seattle, WA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper rack roller cracked then broke
First removed the end cover and clip on the end of the rack slide. Used a flat head screwdriver to push in the clip and carefully pried it out. Then using the same screwdriver, pried up on the rack roller clip attached to the dish rack. Once clip was free of the rack, slid the rack roller off through the front of the slider. Slid the new rack roller into the slider and snapped the roller clip onto the dish rack in the same place the old one was. Carefully twisted the plastic end cover and clip back onto the rack slider. Job complete. The trickest part of the job is removing the rack slider end cover.
Parts Used:
WHEEL
  • Jeffrey from Wilson, NC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!