Models
>
N9608W0
N9608W0 Roper Range - Overview
Sections of the N9608W0
[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Idler Pulley Assembly
PartSelect #: PS11743765
Manufacturer #: WP691366
This part provides the tension required for a multi-ribbed belt. It also helps the belt rotate the drum and attaches to the idler pulley wheel. If your dryer will not start or tumble, takes too long t...
$17.64
In Stock
Surface Burner Plug-In Block Kit
PartSelect #: PS340571
Manufacturer #: 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to...
$13.42
In Stock
Lint Filter with Handle
PartSelect #: PS345247
Manufacturer #: 339392
This filter collects lint as it passes through the dryer vent.
$36.84
In Stock
Delta Frame Surface Unit - 6 Inch
PartSelect #: PS11757480
Manufacturer #: WPY04100165
This is a delta frame surface unit, also known as coil element, for a stove, range, or oven. It is a 6-inch surface burner with a reinforced delta frame that carries 1250 watts and 240 volts. The burn...
$50.86
In Stock
Temperature Sensor
PartSelect #: PS388521
Manufacturer #: 8053344
This temperature sensor is used with self cleaning ovens. Its 1000 ohm resistance increases with temperature. This sensor has male leads and comes with ceramic wire nuts.
No Longer Available
Burner Switch Kit
PartSelect #: PS373020
Manufacturer #: 4391989
This surface burner control switch kit comes with screws, mounting plate, push on locking nut, shaft adapter, and instruction sheet. The burner switch is universal for 6 and 8 inch elements. It featur...
$37.68
In Stock
Hex Nut
PartSelect #: PS11738304
Manufacturer #: WP112432
This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts an...
$8.04
In Stock
Delta Frame Surface Unit - 8 Inch
PartSelect #: PS340503
Manufacturer #: 326789
This electric range delta frame surface element with looped terminal ends measures eight inches and has five turns. It carries 2600 watts the center medallion is black in color.
$91.53
In Stock
Dryer Drum Baffle
PartSelect #: PS11741750
Manufacturer #: WP342847
The drum baffle lifts and tumbles the clothes inside the drum as the drum rotates during the drying cycle.
$85.65
In Stock
Oven Thermostat
PartSelect #: PS11742378
Manufacturer #: WP4337360
This Harper Wyman style 6707 series oven thermostat has a temperature range between 150 degrees Fahrenheit and 550 degrees Fahrenheit, as well as a fixed broiling temperature. There is an "off" positi...
No Longer Available
Questions And Answers for N9608W0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the N9608W0
[Viewing 7 of 7]Element will not heat
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
F3 Error message
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the strin
... Read more
g still shows thru the back. If you don't you have a 15 minute job trying to fish the wires at an angle thru the insulation (a very frustrating task). Untie the string from the old and tie it securely to the new. Pull the string from the back and Voila! your new sensor can be plugged in or wirer nutted to the old connection on the back of the stove. Replace the nut and the two screws and you're done!
Read less
Parts Used:
-
Charles from Brecksville, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
157 of 198 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed new Lint Filter for Dryer
Went to 3 big appliances stores - Not one carried any type of Lint Filter for Dryer. Went on line & typed in Lint Filter for Dryer in search bar. Part Select came up. Went thru site to ordering - Part Select made so easy to order. You just type in your Manufacture name & they instruct you step by step how to find model number & type o
... Read more
f filter you need. So Easy. Very economical. I ordered & within 4 days I had my filter. I used 7-14 day delivery & was so pleased I had my filter within 4 days. Parts Select sent me email verifying my order as well as email when the part shipped.
Wonderful Customer Service. I will definitely use Part Select for any need part on any appliance.
Easy - Economical & One Stop Shopping. Love it
Wonderful Customer Service. I will definitely use Part Select for any need part on any appliance.
Easy - Economical & One Stop Shopping. Love it
Read less
Parts Used:
-
Diane from Rancho Cucamonga, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
65 of 69 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would not heat
First i shut off the power since this is an electric cook top/range. I then removed the knob and the two screws that hold the burner switch in place. I removed the wires one at a time and connected each to the new switch. I then reattached the screws to the switch. The most difficult part to me was breaking off the switch stem at the
... Read more
right level. I got that done and finally selected the appropriate adapter for the stem/knob fit.
Read less
Parts Used:
-
Edward from Malvern, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
27 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!