My Orders
N66BC-1 (Type 0) Bostitch Nailer - Overview
_WW_1.gif "Page A Diagram and Parts List for Type 0 Bostitch Nailer")
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$50.77
In Stock
KIT-TRIGGER VALVE
Part #TVA6
This is a genuine Bostitch replacement part that fits all BT brad nailers and all S32 staplers. If trigger leaks air or if tool misfires often, try replacing trigger valve. This kit contains one (1) each of: valve assembly (including both O-rings), lubricant, spring pin punch, and repair instructions. Please note that two (2) O-rings are ...Read moreincluded but can also be purchased separately as parts # 106967 and # 86459. O-rings are easily damaged and worn out, causing tool issues, so it\\\'s a good idea to have a backup or two on hand. Only a hammer is needed for this repair.
Read less
$6.40
In Stock
SEAL RING
Part #P2320006600
This is a genuine replacement seal ring supplied directly from original equipment manufacturer. It is a commonly used item on Bostitch nailers. This plastic part fits over the piston to provide an air tight seal. Over time seals would deteriorate and crack allowing for air leaks. Please note this item is made out of rubber material and it is sold individually.
$6.40
In Stock
O-RING
Part #S06S003600
This part is OEM and is compatible with various Bostitch nailers. An O-ring is a vital part that, when damaged or incompatible, can compromise the functioning of a tool. It acts as a flexible pressure seal between rigid parts. Sold individually.
$11.95
In Stock
END CAP
Part #9R209578
This replacement end cap is specially designed for use with Bostitch nailers. It is supplied directly from original equipment manufacturer and it is sold individually. This end cap is helps to provide a seal for the air chamber. It is the part that the pressure hose would connect to. It is made out of metal and it is sold individually. Pl...Read moreease note the o-ring is sold separately. Replacing this item is a simple task that should only require a wrench. • Make sure the unit is unplugged • Remove the old end cap • Secure the new cap • Test the unit
Read less
$6.40
In Stock
O-RING
Part #851483-S
This item has been OEM sourced to ensure a high level of quality. The o-ring is intended to be used with pneumatic nailers from Bostitch, Porter Cable, and DeWalt. The o-ring is used to seal the connection between the nose and the bottom of the cylinder. This item is sold as an individual replacement part.
$9.11
In Stock
Piston Head Valve
Part #174054
Restore reliable firing power with this piston head valve, a key component that controls airflow within the nailer's cylinder assembly. By directing air pressure to drive and return the piston during each firing cycle, it helps maintain consistent performance and efficient operation. A worn, cracked, or damaged valve can cause air leaks, ...Read morereduced driving power, or improper cycling, making replacement an important step in restoring tool performance. Because internal component locations can vary between models, refer to your tool's parts diagram or service manual to confirm the correct placement before installation.
Read less
$18.10
In Stock
0-RING
Part #86460
This is an authentic Bostitch replacement part, sold individually. O-rings are designed to withstand thousands of pounds of pressure by creating a seal between two or more parts. This O-ring is compatible with the staplers and nailers listed below.
$11.87
In Stock
GASKET-FRAME/DEFLECT
Part #174050
This item is an authentic OEM sourced part that is intended to be used with pneumatic nailers from Bostitch. The gasket is used to seal the connection between the deflector assembly and the frame of the nailer. A hex driver may be needed to install this item, please note the gasket is priced as a single item.
$6.40
In Stock
O-RING-45.5MMX2.0MM
Part #174058
It is a genuine OEM supplied replacement part and is specially designed for Bostitch nailers. The purpose of this o-ring is to provide an air-tight seal for the cylinder, over time it may wear out and begin to crack eventually requiring a replacement. Make sure to refer to the appropriate diagrams of your model for the correct location an...Read mored application of this hardware. Keep in mind this high-quality component is made of durable rubber material and is sold individually.
Read less
$6.40
In Stock
O-RING-41.0MMX1.78MM
Part #174044
This is an authentic manufacturer-sourced replacement o-ring which is specially designed for use with Bostitch nailers. It helps to provide an air-tight seal for the exhaust cover, over time it may deteriorate and crack eventually requiring a replacement. Please note this high-quality component is made of durable rubber material and it is sold individually.
$32.87
In Stock
KIT, CONTACT TRIP CONVERSION
Part #CNTK1
This authentic OEM sourced component is made for use with Bostitch nailers and staplers. It is a special contact trip conversion kit that can be installed on the tool to fire upon contact with a surface. Please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of th...Read moreis component. Keep in mind this high-quality kit is made of durable metal and is sold individually.
Read less
$6.40
Special Order
O-RING
Part #S06P000400
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More