This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out a...Read mores required if your oven is rocking. It is recommended to check the other three leveling legs on your appliance in case they are also damaged or worn. The leveling leg measures 1.859", is all black in color, and is made entirely out of plastic. This leg may be shorter than the original but is the factory replacement. Longer leg is not available.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This door seal is used for ranges and ovens. The seal prevents hot air escaping from the oven to maintain a certain temperature when baking. The clips sticking out of the seal help secure it to the range doors for the most effective performance. This seal is black in color and is made of rubber. If your oven is not heating evenly, has lit...Read moretle to no heat when baking, or is too hot, replacing the seal can solve the problem. The tools needed for this repair are needle nose pliers. Make sure the oven is cool before starting this installation project. Refer to the diagram provided by the manufacturer for further installation instructions.
This is a thermostat knob, but you may know it as a surface burner knob. It is a part for the stovetop on your range. It gives you the ability to control the heat levels of the surface burner, located on the stovetop of the range. This knob is all black in color and accepts a D-shaped shaf.t It has a diameter of 2 inches.
This is a surface burner knob for the stovetop on your range. it is 2 inches in diameter and only accepts a D-shaped shaft. The part snaps into place on the shaft of your unit and rotates to the different selections available, allowing you to choose the temperature levels. The most common reason for needing to replace this part is if your current one has worn over time and needs an update.
This set of four square chrome drip pans is designed to catch spills and protect the surface of select gas ranges and cooktops. Each pan measures just over 8 inches per side with a 3.5-inch center hole, providing a precise fit for the burner area. Constructed from chrome-plated metal, these OEM components offer durability and a polished a...Read moreppearance that complements most kitchen styles. By preventing food debris and liquids from reaching internal components, the drip pans help maintain appliance cleanliness and performance. Ideal for replacing worn or discolored pans, this kit is compatible with a variety of models and restores both function and aesthetics to your cooktop.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
worn out door seal
31 of 32 peoplefound this instruction helpful.
Stella from Charlotte, TN
Really Easy
Less than 15 mins
Pliers
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.
Was this helpful?
Thank you for voting!
Door Seal on oven was old, hard and breaking apart.
10 of 11 peoplefound this instruction helpful.
Kenneth from Friend, NE
Really Easy
Less than 15 mins
Pliers
It was very simple, pull off the old one, then I took some pliers and pulled out the fasteners. Took new gasket from bag and it just snapped into place.
Was this helpful?
Thank you for voting!
Seal was fallinig off
7 of 8 peoplefound this instruction helpful.
Marilyn from Fresno, CA
Really Easy
Less than 15 mins
My husband did it. I was not there to see it. He said it took less than one minute, just snapped in and worked beautifully.