This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually.
NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.
This high-voltage diode is designed for use within various makes and models of microwaves and is a genuine OEM part that converts alternating current (AC) into direct current (DC). If you notice your microwave turns on and starts but does not heat anything, this diode is likely responsible. You can check the continuity of the diode with a...Read more multimeter before outright replacing it, but it is important to remember that doing any repairs on a microwave and dealing with sensitive electrical components should be done carefully and with the appropriate precautions to avoid any hazards. To replace the high-voltage diode in your microwave, disconnect it from power and allow it to discharge. Using the appropriate screwdrivers, gain access to the control panel of the microwave. Using an insulated screwdriver, release any electrical charge in the capacitor by touching it across the terminals. Then you can remove any hardware securing the diode, including the harness connecting it to the capacitor, which may be easiest done with pliers. Connect the new diode to the capacitor terminal and the securing bracket, and then reassemble your microwave before connecting it to power again.
This is a cooking tray, but may also be known as a turntable tray, and it is used in conjunction with your microwave or oven/microwave combo. The outer diameter of this part is roughly 12.75 inches. The tray is made entirely of glass and is colorless. The purpose of this part is to act as a stable and even cooking surface for your food to...Read more sit on during a cooking cycle. To ensure a more even cooking temperature the tray will also spin when your appliance is activated. The most common reason for needing to replace this part is if your current one has been damaged.
This genuine microwave door switch lever is an essential component of the door interlock system, helping detect when the microwave door is properly closed so the appliance can operate safely. Designed to engage the door switch mechanism during opening and closing, it helps ensure the microwave starts only when the door is securely latched...Read more. Replacing a worn, cracked, or damaged lever can help resolve issues such as a microwave that will not start, intermittent operation, or failure to recognize that the door is closed. Made from durable plastic for reliable performance, this OEM replacement part helps restore proper door switch function and safe appliance operation. Installation typically involves disconnecting power, removing the outer cabinet or control panel as required to access the door switch housing, replacing the damaged lever, and reassembling the unit before testing operation. This is just the lever, not the switch itself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
microwave oven blew fuse
27 of 43 peoplefound this instruction helpful.
tad from tamarack, MN
Really Easy
Less than 15 mins
Pliers, Screw drivers
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read moree help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix .
Read less
Was this helpful?
Thank you for voting!
Buzzing noise, no heating of food
22 of 35 peoplefound this instruction helpful.
Ted from Hudson, NH
Easy
30 - 60 mins
Pliers, Screw drivers
Removed control panel, discharged HV capacitor. Removed old diode, tested to confirm failure. Replaced part. Other than the removal of the panel swapping the part was almost as easy as replacing a light bulb.
Was this helpful?
Thank you for voting!
microve stopped working
15 of 30 peoplefound this instruction helpful.
Denice from Montgomery, AL
Really Easy
15 - 30 mins
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise