This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging the drive motor to rotate the washer basket. The kit includes the clutch assembly, cam ring, spring, basket drive gear, pulley, and mounting n...Read moreut. Replacing this component can resolve issues such as noisy operation, slow or failed spinning, poor agitation, and excessive moisture in clothes after a cycle. In some cases, a burning smell may also indicate a failing clutch. Installation requires basic tools and should be performed with the appliance disconnected from power. Compatibility should be confirmed using your washer’s model number.
This basket drive hub kit is a vital component in select washing machines, designed to connect the wash basket to the central drive shaft, enabling proper rotation during wash and spin cycles. It plays a key role in transferring motion from the motor to the basket, ensuring effective agitation and spinning. Constructed from durable materi...Read moreals, the kit typically includes the drive hub, a retainer, and installation instructions. Common symptoms of a worn or damaged hub include failure to agitate, slow or no spinning, excessive wobbling, and unusual noise during operation. Replacing this part is a common DIY solution and can restore the washer’s performance. Installation requires basic tools and moderate repair experience.
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the belt enables the drum to spin and agitate during wash and spin cycles, ensuring effective cleaning and rinsing. Manufactured to Whirlpool’s ...Read morespecifications, this replacement part offers reliable performance and a precise fit. Common symptoms of a worn or broken belt include the drum not spinning, unusual noises, or a burning smell during operation. Replacing the belt can restore proper function and prevent further mechanical issues. Always verify compatibility with your specific model before ordering.
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your washing machine is experiencing issues starting or if the lid is not securing, this lid lock assembly likely needs to be replaced. This lid lo...Read moreck attaches underneath the top portion of your washer and its wire harness connects to the rear of the appliance. To replace this assembly, you will need a screwdriver, flathead screwdriver or putty knife, and wrench. This lid lock is an OEM part that is sold individually and does not come with any other parts or accessories.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This 6-pin shift actuator is an authentic OEM part supplied directly by the manufacturer for use in washing machines. The shift actuator is responsible for controlling the movement of the washer transmission during the different phases of the wash cycle. This allows the washer to switch between agitating and spinning modes. Signs of a fau...Read morelty shift actuator include the washer failing to agitate or spin, incomplete cycles where the washer gets stuck in one phase, or unusual noises during operation
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Luis - For model number MVWC416FW0
March 29, 2023
Repair the Agitator (It's the one in the middle of the Maytag HE Washer that has a top which Reads : Fabric Softener Dispenser) . The round plastic ring on the bottom broke and fell out of the plate it sits on. I was looking for the tutorial Video Maytag has on how to replace it but none was not available for the Agitator (unless I overlooked it) Can you please help me out on how to repair and replace the part. THANK YOU so MUCH!!
Hello Luis, thank you for contacting us. We are providing you with a relevant video that will help you in replacing the agitator. We hope this solves your problem!
9 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
DAVID - For model number MVWC416FW0
February 5, 2020
This washer is loud when going into a spin cycle alot like the overused washers in the laundermats. It still works but is something starting to wear out on it?
Hello and thank you for writing.
It certainly sounds like it could be a faulty drive pulley PS10057144 and/or a loose or a faulty belt PS11747978 you should check the part(s) for signs of damage, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
Hi Jack,
Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet. Before you replace the tub ring on your washer, use tape to secure the lid. Then remove the top 2 rear hinge screws from the rear panel. Then remove the 2 screws securing the wiring and tube cover and pull it off. Next, pull the main top forward and then lift it up and support it. Then use a flathead screwdriver to remove the tabs securing the tub ring and then pull it off. Then install the new tub ring by aligning the tabs on the ring with the catches on the outer tub and snap it into place. Then remove the support and then lower the top and align the slots in the top with the bracket tabs on the frame and push the top back. Then reinstall the wiring and tube cover and then reinstall the hinge screws. Remove the tape securing the lid. Plug the washer back in and it should now work for you. We hope this helps. Thank you and have a great day.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Deb - For model number MVWC416FW0
March 13, 2020
When wash is in spin cycle it makes loud roaring sound.What parts are wearing out?
Hello Deb, thank you for writing. When you Washer is making a loud noise during Spin Cycle it could be a number of parts that may have worn out or gone loose. We advise checking these parts for damage: Main tub bearing faulty, Main drive pulley, Motor coupling worn, Bad clutch, Worn out drive belt.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Frank - For model number MVWC416FW0
February 25, 2020
Green light continues to flash on sensing cycle with no results
Hi Frank,
Thank you for your question. If the sensing light is flashing, then the cycle has paused. To resolve this, press the pause button once. The light should remain on, but it should stop blinking. Depending on the water pressure, the wash cycle should continue. The flashing could also indicate that the water may filling the washer slowly. You will need to check the hoses and the screens and clean them if they are clogged or dirty. You should also check the water inlet valve to make sure that it is working correctly. You will need to test the valve with a multi-meter. Before beginning, ensure that you have unplugged your washing machine. The water inlet valve will most likely be found directly behind the hose connections. You will need to remove the rear panel in order to access it. Once you have located it, remove the valve in order to test it. Before testing it, inspect the screens inside the pump and the pump itself for any debris or damage. Be very careful when doing this as screens cannot be replaced, and if they become damaged the entire valve will need replacing. Set your multi-meter to Rx1 and touch the probes to the terminals. The reading of a functional valve varies from model to model, refer to your owner’s manual to determine what your reading should be. If you do not receive the recommended reading, you will need a replacement water inlet valve. You should check the water level switch and pressure hose to make sure they working. Inspect the switch for any signs of wear, burning, cracking, or damage. If the air dome hose is not damaged or if your switch shows any the symptoms above, you may need a replacement water level switch. Flush the hoses before putting them back on to make sure they are clean and make sure the water pressure is good. We hope this helps. Thank you and have a great day.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Noise on bottom of Washer louder as time went on. 1 1/2 years
95 of 129 peoplefound this instruction helpful.
Jerry from WALLA WALLA, WA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers, Socket set
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Noise, grinding sounds. Wash tub stopped turning but motor and cycles kept functioning. Process of elimination, must be the clutch assembly.
71 of 107 peoplefound this instruction helpful.
David from BLOOMINGTON, IN
Easy
30 - 60 mins
Screw drivers, Socket set
Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.
Was this helpful?
Thank you for voting!
Hub had warn its grooved teeth off and washer wouldnt agitate
65 of 91 peoplefound this instruction helpful.
Allison from RICHFORD, NY
Easy
15 - 30 mins
Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
My Orders
