This is an inlet valve for your washing machine. The inlet valve is an electrically controlled valve with a solenoid that opens and closes as needed, during the water filling cycle of the washing machine. This inlet valve features two inlets, one for hot and one for cold water, and three push-on valves that connect within your washing mac...Read morehine. If your washer is having issues filling or is leaking water from the area of the inlet valve, it needs to be replaced immediately. Replacing this valve will require a screwdriver and a wrench to replace. This inlet valve is an OEM part and is sold individually.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This lid lock assembly is supplied by the original manufacturer for use in various models of top-load washing machines. The assembly includes the lid lock mechanism and the wiring harness. You can find it positioned on the underside of the washer lid. The lid lock assembly is designed to prevent the washer lid from opening during use. Thi...Read mores is a safety mechanism that ensures that users do not accidentally come in contact with moving parts or are not injured by spilled water or detergent. If the lid lock assembly is faulty, the washer may be unable to start the cycle or it may stop in the middle of a cycle.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
This agitator assembly is an authentic OEM part that is compatible with various models of washing machines. It consists of a central shaft with a series of fins attached to it. When the washer is operating, the agitator rotates back and forth, causing the clothes to rub against each other and against the agitator itself, which helps to lo...Read moreosen dirt and stains. If the agitator does not move or moves erratically while the washer is running, then this is a sign that it is faulty. You may also hear unusual noises such as grinding or rattling and notice that your clothes are not distributed evenly around the agitator during the wash cycle.
This is a dispenser drawer assembly direct from the manufacturer and used in washing machines. This drawer is made of plastic and features the compartments for bleach, detergent, and softener, for you to pour each respective liquid into. If your current dispenser drawer is clogged or moldy beyond repair, it should be replaced. Removing an...Read mored replacing the old drawer is simple and requires you to press down on the respective tabs to release it from the washer assembly, then simply slide the new one in. When installing the new drawer, make sure to close the lid slightly so the dispenser will slide right in as it is supposed to and sit flush. This drawer is sold on its own, and does not come with any other parts or accessories.
This is an impact absorber, also known as a sound dampening pad, for washing machines. This sound dampening pad attaches to the top of your washing machine drum to reduce the severity and harshness of vibrations and movement during the washing and spinning cycle, to produce a quieter laundry experience. If your washer is shaking excessive...Read morely during operation, this pad may be worn out or simply missing, and in need of replacement. To replace this pad, you will need a screwdriver or wrench to access the inner portion of your washing machine and remove the old one and install the new one. This OEM pad measures 5-inches by 3-inches and is sold individually.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Scott - For model number MVWB765FW3
January 5, 2022
Washer makes an extremely loud grinding sound (sounds like a garbage disposal) at the very end of the drain/spin cycle. Last for several Seconds and than stops
Hello Scott, Thank you for the question. This is normally an indication the Washer Drain Pump is blocked, damaged or faulty and may need to be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
The agitator has raised up from the bottom of the tub and sucked a bed sheet under the agitator and won't come out.
Hello Cliff, Thank you for the question. Sounds like the Agitator was loose. Under the cap at the top of the agitator there is a bolt you can remove. Once removed, the Agitator will come off the post so you can remove the Sheet. You just need to reinstall the agitator and make sure it is secure to avoid material getting caught up again. We hope this helps!
Under the schematic for Console and Dispenser for this model it shows a part listed as #26, is this part the faceplate for the console, and is it available?
Hello Everett, thank you for your question Item #26 is Overlay PS12347692 without electronics( we have a photo on our site). The overlay is stainless steel with black screen printed graphics on it .The Electronics is the part PSPS16217891. Thank you and have a great day.
I have to unplug the washer and wait a few minutes before replugging it in for it to start a wash load. Is this the control board or the lid lock? Or something else?
Bill
Hi Bill,
Thank you for your question. If the washer will not start after filling with water, you will need to check both of these parts. Before removing and checking these parts, unplug the washer from the electrical outlet. When inspecting the lid switch, check to see if it works mechanically and to see if the actuators and levers are damaged or sticking. If they are fine, you will need to test it for continuity with a multimeter on the Rx1 setting. You should receive a reading of zero. If you get any other reading, you will need to replace the lid switch. For the electronic control board, inspect it for signs of damage, wear, scorching, or burn marks. If it shows any of these signs, you will need to replace the electronic control board. We hope this helps!
Washer completes cycle. When I go to put them in the dryer they are really wet.
If I leave over night. The next day pump is pumping and water is slowly adding water . For hours. No display on the face. Hit power button....no response.
I have to unplug and it seems normal.
Hello Camille, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the control board, part number PS16217891, to solve the problem. A malfunctioning control board can most probably cause this problem. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud grinding noise when the washer was in use.
69 of 84 peoplefound this instruction helpful.
Charles from STARKVILLE, MS
Easy
1- 2 hours
Nutdriver, Screw drivers, Socket set
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate
... Read more( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Read less
Was this helpful?
Thank you for voting!
Broken lid frame at left hinge.
37 of 43 peoplefound this instruction helpful.
Greg from RICHMOND, VA
Easy
30 - 60 mins
Socket set
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge
... Read more. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.
Read less
Was this helpful?
Thank you for voting!
Lid was broken at the hinge and would not stay closed
24 of 29 peoplefound this instruction helpful.
Gary from GLADE VALLEY, NC
Easy
15 - 30 mins
Removed the old lid by removing the two screws on both sides of the lid holding it to the hinge. Then pull upon the lid to remove. Slide the new lid back on the hinges being careful to slide in the right slot in the lid. Replace the screws through the lid into the hinges and your done
My Orders
