MQU1556AEW Maytag Freezer - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

Removed shelves from inside freezer then removed 4 screws holding cover panel. Pulled panel up and slightly pulled forward to remove. Removed wiring connections then removed two screws that held the motor & fan assembly. Removed the support bracket from the old motor and installed same on the support bracket. Reversed removal procedur ... Read more es for installation. Cover panel is a little bit of a problem when trying to reinstall. Put in panel as high as you can and then slide down. You must then exert a little pressure on the bottom portion to get it to seat correctly. Install four remaing screws and you are done. I had this repaired previously by a professional repairman and noticed from the pictures you folks provided that he had installed the screws on the support bracket incorrectly. That was the reason for the fan blade to rip apart.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

The first thing I observed was the bolts that attach the motor to the mounting bracket were installed backwards at the factory. This caused the fan to catch on the bolt ends which resulted in the motor burning up. When I installed the new motor, I reversed the bolt direction. There is no way the fan will catch. The freezer works great ... Read more !

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

the gasket peels back to reveal the approx 20 screwsholding gasket and door shelves. removed these. removed old gasket from door panel. new gasket needs to be stretched to get on door panel. align screw holes in door panel with screw holes in gasket. attached back to freezer door. this gasket did not seal securely when closing door. ... Read more this gasket was installed on a cold day in a garage and may become more flexible as it warms up.

Turn off power to freezer. Removed two shelves, removed four phillip screws and cover. Used 5/16 nutdriver to remove two fan motor bracket bolts. Did not disconnect wiring, had enough room to flip motor over and remove broken fan blade and attach new fan blade. After reading remarks from another home tech, I reversed the bolts holding mot ... Read more or to bracket, so nuts would not come in contact with fan blades again. Still not sure why fan would of slipped down to break. Running good now!

After observing defrost timer go into (and out of), defrost cycle, I checked continuity of heating element. Since heater coil was intact (79 Ohms of resistance), I figured the defrost thermostat (aka bi-metal therm.), had to be at fault. The new part ($17.00), proved my suspicions correct. As I sought to determine if everything worked, I ... Read more had to wait for the temp. to drop below the defrost therm. set point before I would see the heater coil get hot.
To avoid the costly failure in future, I bought a Chaney wireless therometer with two remote sensors. Sensors require lithium batteries. $30.00 for both are a cheap insurance system.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

When we discovered that the freezer was not holding temperature we quickly moved everything we could to the freezer compartment of our refrigerator. I then removed the shelves and basket from the freezer.
I used a Philips screwdriver and removed the 4 screws from the panel at the rear of the freezer. I discovered that 1 of the 4 f ... Read more an blades had broken off and was laying in the bottom of the freezer. I plugged the freezer in and found that the motor was not running. I removed the bracket which holds the fan and motor with a socket wrench.

When I received the fan and new motor I installed both by reversing the process.

The only issue I had to deal with was that the auto-defrost wire had to be carefully removed from the old motor plug and inserted in the new plug. Once that was accomplished everything was simple.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The defrost circuit is relatively simple. Just three components and interconnecting wiring. Ensure the timer works first, then check the heater element for continuity. Lastly i jumpered around the temp switch to eliminate interconnecting wiring. You can test the switch by cooling it to see if it opens, but some do not open like the on ... Read more e in this particular Whirlpool until they are well below freezing so you’ll need to take that into account in your troubleshooting. Replacing the switch itself is very simple, it’s two wires and it just clips to the heat exchanger in the back of the freezer behind a metal cover.