Models
>
MME08XW1
MME08XW1 Roper Microwave - Overview
Sections of the MME08XW1
[Viewing 4 of 4]Manuals & Care Guides for MME08XW1
Click to downloadKeep searches simple, eg. "belt" or "pump".
Door Interlock Switch Kit
PartSelect #: PS373050
Manufacturer #: 4392027
This part is a genuine manufacturer door interlock switch kit, also known as primary micro switch or microwave switch kit, for a microwave. The function of this part is to sense when the door of the m...
$85.78
In Stock
SCREW
PartSelect #: PS12728594
Manufacturer #: W11380570
Sold individually. For white and almond models.
$14.15
In Stock
Microwave Screw
PartSelect #: PS11742285
Manufacturer #: WP4158079
This screw is for microwaves.
A qualified technician should install this part if it requires accessing internal components of the microwave or microwave door. High-voltage capacitors can retain a l...
$2.85
Special Order
Diode
PartSelect #: PS11742362
Manufacturer #: WP4313101
This part allows power to go one way but not the other.
No Longer Available
Questions And Answers for MME08XW1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MME08XW1
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave worked intermittently depending on how door was closed
Remove top grille (2 screws), undo control panel (1 screw). Tilt down control panel, switches are on the left. There are actually three switches that are involved with the door, two horizontally mounted, one vertically mounted. This would be an EASY REPAIR, but it took me a while to figure out which of the three switches was bad, and a
... Read more
lso took a while to figure out that there is a plastic rod that inserts through the hole in the switch body. Once i figured this out went like a breeze. Lower horizontal switch was the bad one, but since the kit came with two switches i went ahead and replaced the upper horizontal one as well. IT appears that the horizontal switches are probably more likely to fail than the vertical switch based on the position of the switch and force angles. Works great now!
Read less
Parts Used:
-
Robert from Bainbridge Island, WA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
67 of 82 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave went dead while in use.
1. removed vent across the top to gain excess to Screw holding control in place. 2. Removed control panel to access Fuse. 3. Remover fuse after pulling plug. 4.Tested fuse for continuity with volt ohm meter noting no continuity.5. Orderd new fuse. 6. receeived new fuse and installed infuse holder.7. plugged microwave plug back in receptic
... Read more
al and tested unit now working OK.Reversed steps 2 & 1 job complete
Read less
Parts Used:
-
Keith from Georgetown, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
34 of 41 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Close the door on the microwave, punch in the # nothing happened
I removed the unit from the wall. Took the cover off. Set the unit on its side. It revealed the working parts. Removed the old micro switches. Put in the new oness. Presto, it worked. Very easy for me.
The parts was delivered almost before my notice they were shipped.
The parts was delivered almost before my notice they were shipped.
Parts Used:
-
Robert S. from Stafford, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
15 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!