MH75TKFA Master Heater - Overview

This is a photocell designed for use in space heaters to detect the presence of a flame, ensuring that the burner ignites and remains lit to provide heat while preventing the release of unburned gas. This photocell is a genuine OEM part, sold individually, and is compatible with various heater models. It is typically attached to the main ...Read morecombustion chamber with a bracket (sold separately). Factors like dirt and debris, aging, and exposure to higher temperatures can lead to photocell failure. A failing photocell can result in your heater not starting, starting intermittently and then shutting down, and sometimes displaying error codes related to the photocell. To replace this part, you will need a screwdriver and/or socket wrench, as well as a set of pliers. Begin by disconnecting the heater from its power source and draining the fuel from the heater. Remove the top, back, and side covers of the heater to access its internal components. Locate the photocell within the heater, disconnect its cable and the photocell itself, and then install the new photocell. Reassemble your heater, ensuring that any disconnected wires are properly reconnected.

This item is a genuine OEM sourced replacement part that is intended to be used with forced air heaters from Pro Temp, Heat-Stream, Heat Hog, and Master. The plastic fuel filter connects to the fuel line and is used to prevent contaminants from entering the motor assembly. This item is available as an individual replacement part.

It is a genuine item that is supplied by the original equipment manufacturer. This part is made for use with kerosene forced air heaters. The thermostat acts as a sensor which protects the unit from overheating. Unfortunately, over time it may wear out, get damaged or stop working all together eventually requiring a replacement. Note, thi...Read mores high-quality thermostat limit control is sold individually. To replace it, you will need a screwdriver to take the housing apart. Make sure to refer to the owner's manual and the appropriate diagrams for your model to ensure the correct application.

This is a genuine OEM replacement part designed for use with Pro Temp, Heat Stream and Master kerosene forced air heaters. The line is utilized to deliver the fuel from the tank into the carburetor. When you press the primer bulb, it will purge all the air out of the carburetor and fill its chambers with fuel. The excess fuel is then forc...Read moreed back into the tank through the return line. Unfortunately, over time lines will become brittle and may begin to crack eventually requiring a replacement. Keep in mind this high-quality part is made of durable rubber and is sold individually.

This ignitor in a heater, also referred to as a spark ignitor, is a genuine OEM replacement part designed for heaters. It is responsible for the ignition of the fuel-air mixture. If you are having difficulties starting the heater, noting low power output, or experiencing misfires, the ignitor will need to be replaced if the spark plug is ...Read morefunctional. The ignitor can fail due to wear and tear over time, causing it to crack or break or it may experience electrical failure. First, ensure the heater is switched off. Remove the equipment housing and locate the faulty ignitor. Disconnect the cables and primary plug and gently pull out the ignitor and replace it with the new ignitor. Reconnect the cables and plug and reattach the equipment housing. Note that this ignitor may need a plug adapter, part number: 70-037-5000.

This is an authentic Craftsman replacement part that is sourced from the original manufacturer to be used with kerosene forced air heaters. Fuses are used to block excessive electric current from damaging or overheating other part assemblies along the circuit. If the part is damaged or is missing, this will provide an identical replacemen...Read moret for the original component that was installed on a new unit. Check the owner's manual and the appropriate diagrams for your model to ensure the proper repair procedure. Keep in mind this high-quality fuse is sold individually.

This is a genuine manufacturer-approved part which is designed for kerosene forced air heaters. It is part of the tool handling the on/off operation. Unfortunately, over time components may wear out and begin to fail eventually requiring a replacement. Note, this high-quality plastic body switch is sold as an individual item. Refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

This is a Genuine OEM replacement parts used on certain Kerosene/Diesel Forced Air Heaters. This kit includes an air inlet filter, an outlet filter and a lint filter. Its purpose is to filter out dust and debris from contaminating and damaging the motor assembly.

The end pump cover is made of metal. This is available as an individual replacement part. This is an authentic OEM part for heaters made by Pro Temp, Heat Stream, Heat Hog, and Master. A wrench may be helpful when replacing this item. It will need to be replaced if it becomes broken.

This is an authentic OEM sourced replacement gauge which is specially designed for use with kerosene heaters. The gauge registers pressure readings, over time it may wear out and begin to fail eventually requiring a replacement. Keep in mind this high-quality item is made of durable materials and is sold individually. Please make sure to ...Read morerefer to the appropriate diagrams of your specific model for the correct location and application of this item.