This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and should be replaced. The bulb attaches directly to an appropriate light socket and has a small screw-in base. To access the exterior light bulb,...Read more you will need to remove the panel on the bottom of the microwave using a Phillips screwdriver. If your exterior light bulb has not been changed before, it is probably held in place with some silicone. You will need to cut away this silicone to remove the old bulb. If you cannot access the silicone with a utility knife, it can be removed using dental floss. Once the silicone is removed, simply unscrew the old bulb, and replace it with the new one. Be sure to disconnect the power to the microwave before you begin this repair. This light bulb measures about 1 1/8 inches. We do not recommend using a higher-wattage bulb for this appliance, and can only recommend this specific bulb. If fixing the bulb does not solve your microwave light issue, it's possibly a problem with the socket, which means the socket and/or board will need to be replaced. This can be a more dangerous repair, so consult your user manual or a technician before attempting.
This a genuine OEM microwave cooking tray. It is also known as a microwave turntable or microwave plate. The function of the tray is to hold and rotate food items while the appliance is in use to ensure the food is being heated evenly. This cooking tray is made of transparent glass, and may need to be replaced if the tray is cracked or br...Read moreoken. A broken tray may prevent it from rotating if the three partial circles on the bottom of the tray will not connect to the turntable driver. This part is sold individually and is approximately 12 inches in diameter. It is recommended to check the drive coupling, or turntable driver, if tray is not turning.
If the microwave exhaust fan is not circulating air properly, there could be an issue with the grease filter. A dirty filter will cause your microwave to run less efficiently and can alter the taste or smell of your food. Filters should be changed every six months for maximum performance. These silver, aluminum filters are sold separately...Read more, and are approximately 13 3/8 inches long x 5 7/8 inches wide. Measure your current filter to assure correct replacement. Check your grease filters regularly for particles and grease buildup to see if cleaning is necessary. If there is any visible damage to the filter, it should be replaced straight away.
The vent grille mounts to the top of the microwave, above the door. If you notice that your vent grille is damaged, or your door is not closing properly, you may need to replace the vent grille. This vent grille is black in color and is made of plastic. This part is approximately 30 inches in length, by 3.5 inches in height. This part is ...Read moresold individually and can be used on stainless models. Many of our customers have rated this repair as easy. To complete the repair, simply unscrew the damaged vent grille, and screw on the replacement part.
This white plastic vent grille mounts on the top of the microwave above the door, and covers components inside the microwave while allowing airflow through the slats. If the door on your microwave will not close properly, the vent grille could be at fault. If you notice that the vent grille is discolored, cracked, or broken, or if the mou...Read morenting brackets on the grille are damaged or broken, you should replace the part. To replace the part, you will only need a Phillips head screw driver. Make sure this part is compatible with your microwave before ordering. This part does not include the screws used to mount it to your microwave.
This turntable ring in your microwave makes sure that your glass tray rotates smoothly. Located just above the internal floor, it supports the tray so that your food cooks evenly. A broken turntable ring will look warped or cracked. Additionally, the rotation may become uneven or wobbly. You should replace the ring when it is damaged, by ...Read moresimply taking out the old one from your appliance. Please note that this replacement part is sold individually and is a genuine OEM product, specifically designed for your microwave.
The vent grille, used in microwaves, mounts on the top of the appliance and covers parts inside the microwave without blocking off airflow. Instead, the vent allows air to pass through the slats. If the vent is blocked or damaged, it is best to repair the vent grille. To repair, first remove the screw that holds the grill tabs with a Phil...Read morelips screwdriver and clean the vent area. Next, install new grill into the appropriate tabs and make sure to secure the screws to prevent it from falling. Refer to the manual provided by the manufacture for installation instructions and accurate guidance. Remember to unplug appliance from power source.
This door interlock switch is a genuine replacement part designed for use in microwaves. It serves a critical safety function by preventing the microwave from operating when the door is open. Because proper operation of the microwave’s shielding and interlock system is essential for user safety, this part should be installed by a qualifie...Read mored service technician. After installation, the interlock switches and microwave shielding must be thoroughly tested to ensure the appliance meets safety standards.
This diode, or high voltage diode, is used in microwaves. It is an electrical current control device that ensures power flows in one direction and not the other way. If your microwave produces no heat, heats inconsistently, or gets noisy, replacing this part can be the solution. The tools needed for this replacement are a nutdriver, plier...Read mores, and screwdrivers. First remove the microwave cover, then remove the old part by disconnecting the small thermostat. Replace with the new diode. Remember to use the diagram provided by the manufacturer for more instructions.
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an inch long, is metallic on both ends and ceramic in the middle. Before beginning this repair, unplug the appliance and wait a few minutes bef...Read moreore starting. Remove the outer cabinet which is held in place with two screws. You will then locate the power cord which will lead you to the fuse holder. Determine if the fuse has blown. Using an ohmmeter, you should be able to figure out if it has blown. A proper reading is zero ohms, if it reads as anything else then your fuse has in fact blown. Simply snap the old fuse out of place and place the new one in.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marty - For model number MH1150XMS2
March 6, 2020
External (under unit) light does not work. Everything else works properly. The light had been on for several days continuously prior to going out. On inspection, i discovered that the bulb seperated from base, so i suspect there was a circuit overload/overheat. I took the socket out and tested the leads. No ac at the terminals. Is there a breaker for just the external light circuit or do i have a likely circuit board failure?
Hello Marty, thank you for your question. There is no breaker or fuse for the light. If the bulb is good, the socket is tested and is good the issue would be with the board. I hope this helps.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
DINA - For model number MH1150XMS2
July 12, 2021
Why am I getting an f2 message?
Hello Dina, Thank you for the question. The F2 Error code indicates Oven Temperature Is Too High. We suggest testing the Fixed Thermostats and check for continuity. We hope this helps!
Hello John, thank you for contacting us. To adjust the cooking power level on your microwave, you may need to touch "COOK POWER" and then touch number pads to enter power level, if other than 100%. If you need to change the cook power after cooking has started, you can touch "COOK POWER" repeatedly to scroll through the cook power levels and then touch "START" to confirm the change. We hope this information helps!
Was this helpful?
Thank you for voting!
Diana Duke - For model number MH1150XMS2
November 6, 2025
I am trying to find the dimensions of the microwave model.
Hello Diana, thank you for reaching out. The dimensions for your model are: Height 16.25", Width 29.87", and Depth 15.37". We hope this information helps!
Was this helpful?
Thank you for voting!
Jules - For model number MH1150XMS2
February 15, 2020
Our door broke so need new door...
jules
Hello Jules,
Thank you for your question. The microwave door is only available in black fro your model under part PS885550. We hope this helps