Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This gasket retainer clip kit is for freezers. There are 24 pieces in this kit. The clips are what secure the gasket and liner to the freezer lid. The clips are white in color and made of plastic. If ...
This is white touch up paint for refrigerators, microwaves, ranges, dryers, and freezers. It is used to cover, or touch up, nicks and scratches on the appliance from wear and tear. It is an 18ml bottl...
A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This mean...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mickie
June 28, 2021
How many cubic is my freezer
For model number MFC05M0BW4
Hello Mickie, Thank you for contacting PartSelect.com. Very sorry but we do not have the size of the appliance. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the appliance directly. We hope this helps!
Was this helpful?
Thank you for voting!
Aggie
August 9, 2025
This unit turns on for a few seconds then shuts down. Few seconds later on then off again. Does not get cold.
For model number MFC05M0BW4
Hi Aggie, thank you for reaching out. It seems that there is a compressor problem. This short cycling is often caused by overheating, electrical issues, or low refrigerant. Specifically, the start relay or start capacitor on the compressor could be faulty. We would suggest checking the start relay, part number PS471681. You may need to replace it to fix the issue. We hope this solves your problem!
Hello Andrew and thanks for writing.
A failed condenser fan motor can inhibit freezer cooling because air doesn't move across the condenser coils to cool the refrigerant before the refrigerant enters the evaporator. ... A failed electronic control board or a bad thermistor (also known as the temperature sensor) can also cause your freezer to warm up. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
My husband removed the old hinge, by taking out the old screws and the old hinge and attached the new one, by inserting the new hinge and the new screws. It was as easy as 123.
When I received the new gasket I took a blow dryer to it and straightened out the warped areas prior to removing the old gasket. I then looked for a tool to remove the pins holding the gasket in place. I found a butter knife worked the best to get underneath and pry them out. Since this is a chest freezer, the pins in the back of the d
... Read moreoor were very hard to remove and one of them even broke off as I was removing it. Of course I had no spare pins when I went to put the new gasket in place. The new gasket slid right on and the pins snapped into place with a little bit of HARD pressure. My advice is to make sure that you do the back of the door first, since it is hard to line up the holes and the pins otherwise. It would not have been a difficult repair if not for the pins giving me trouble. There are no instructions sent showing how to do any of this work, so if you are not knowledgeable about gaskets this repair could be a difficult one. Maybe the company could include some basic instructions as a help to their customers.
