This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the d...
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
The idler pulley wheel is now sold with this arm. This idler pulley is for dryers.
Idler pulley maintains correct tension on the drive belt to spin the drum.
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Keith
December 21, 2019
Dryer working but no heat
For model number MED6000XW2
Hello Keith and thanks for writing.
It certainly sounds like a failing heater element PS11746337 and faulty wiring # PS334206 you should check for signs of damage, and replace it if needed. It is recommended to replace both parts at the same time. We hope this helps. Please contact us anytime.
My dryer quit heating. I replaced the element last summer but this time wasn't like then. This time it dried one load and the next it didn't heat at all. Could it's be something else?
For model number MED6000XW2
Hi Brian, thank you for contacting us. Based on our understanding of the issue, we would suggest you check the internal-bias thermostat, part number PS11746740, as it is most likely faulty and may need to be replaced. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. When defective you may not have heat inside the drum. We hope this solves your problem!
Dryer turns on, but when you push start button it only clicks !!! Does not engage the drum or anything ???
For model number MED6000XW2
Hello Duke, thank you for your inquiry. The problem seems to be with the Thermostat and you may need to replace it, the part number is PS11746740. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Hi Donald, thank you for reaching out. The compatible door hinge for your dryer model is part number PS11750410. If you require assistance to place an order, please contact customer service!
Will not power up. Receptacle has power. What causes this?
For model number MED6000XW2
Hello Alan, thank you for contacting us. Based on our research, we would recommend checking the terminal block, part number PS11741489, to fix the issue. We hope this helps!
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the
... Read moreunit...works fine
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.