Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
This part has a swivel gooseneck fitting and that allows it to be installed closer to the wall. This part has a 3/4" hose thread on one side and a 3/8" copper tubing on the other side.
The water inlet valve assembly is a crucial component of dishwashers that controls the flow of water into the unit. This genuine OEM replacement part includes the inlet valve, inlet hose, and hose cla...
This heating element is a genuine OEM replacement sourced directly from the original manufacturer for use in various models of dishwashers. The element is designed to heat water inside the dishwasher ...
Enhance the operational efficiency of your dishwasher with this genuine OEM Stop Front Dishrack Stop Clip from Whirlpool. This product is designed to prevent the dishrack in your dishwasher from slidi...
Stay ahead of your kitchen chores with the Whirlpool Dishwasher Drain Pump. Designed to efficiently remove water from the dishwasher tub during the draining phase of your dishwashing cycle, this authe...
We're here to help you get your cooktop working perfectly again with the GE Spark Ignition Switch and Harness. This essential component is explicitly designed for cooktops, and it covers all the chall...
This lower door seal is a flexible rubber gasket designed to create a watertight barrier at the bottom of your dishwasher door, preventing leaks, steam, and detergent from escaping during wash cycles....
$48.45
In Stock
Order now and your part arrives by Apr 23
Questions And Answers for MDB4949SKZ2
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
March 15, 2025
What are the dimensions for this model
For model number MDB4949SKZ2
Hi Ed,
Thank you for your question. The dishwasher measures 23-7/8 inches wide by 24-1/2 inches deep by 33-5/8 inches high. We hope this helps!
3 people found this helpful.
Did this question help you?
Thank you for voting!
Jill
July 10, 2025
How to remove and clean filter
For model number MDB4949SKZ2
Hello Jill, thank you for contacting us. We have attached a relevant video on how to remove the filter. Rinse the filter under warm water, gently scrubbing with a soft brush. Use dish soap if needed to remove debris. We hope this information helps!
My Maytag dishwasher model #MDB49SKZ2 door drops rapidly like a rock when opened. Trying to determine what's causing that. Its only 1yr old
For model number MDB4949SKZ2
Hello Lou,
Thank you for writing in. Our research has found that the hinges have probably gone,
HINGE ASSY-LEFT
PartSelect #: PS18355222 and
HINGE ASSY-RIGHT
PartSelect #: PS18355221 Should do the trick. We hope this helps.
BOTTOM wash bar will not turn. top spins. when filling with water, it thinks full witch it is see a little water getting to come out lower wash bar. i hear a solenoid sound stops, so it puts a little more water in and starts working lower wash bar moves then a solenoid sound then wash bar lower stops. upper wash bar aways works code F8 ANS E4 after i un plug the machines power
For model number MDB4949SKZ2
Hello Michael, thank you for getting in touch. Based on our research, the error code F8E4 indicates an overflow issue, meaning the dishwasher is detecting excessive water, likely due to a leak or a faulty control board. This problem is most probably stopping the lower spray arm of your model to function properly. We would recommend checking the dishwasher for any internal leakage. If the problem persists, then you may need to check the main control board, part number PS16875887, to solve the problem. We hope this helps!
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
After pulling the dishwasher out, I was able to determine the leak was occurring around the plastic nuts on the end of the heating element. I removed the heating element and saw that even though there were washers on the ends that protruded through the backside of the machine, they really weren't sealing the holes the element was sticking
... Read more through. Looking at YouTube videos on the installation procedure, I noticed the element being installed had a sort of metal grommet permanently affixed to each end and the rubber washers were between the grommet and the dishwasher body. I ordered the new part and saw this to be when I received the new part. This grommet allowed the washer to seal the hole, once the plastic nuts were installed on the backside of the dishwasher. This seems to have stopped the leak. I don't know how the original part ever worked correctly, since the washers freely sat on the element with nothing to force them up against the body of the dishwasher and seal the holes. It may have been leaking long before I discovered the problem.
The valve has a plastic fitting to attach the the water line with a hose fitting. Was not carful enough with the original and damaged it attaching the water line. Ordered a replacement fitting. While it is possible to replace the water inlet valve without pulling the dishwasher out from the cabinet found it was easier to get at with the m
... Read moreachine out. The video does and good job of showing the removal and replacing the valve. Easy job, don't be like me and be careful attaching the water line.
