LZ26KC604 (252000-259999) Exmark Lawn Mower - Overview

The Ni Lock Nut (Nylock Nut) is a Silver, 5/16x18, individually sold metal nut. It can be adjusted and replaced using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place on the augur. These nuts are a one time use part due to their locking mechanism. You'll know the nut has...Read more broken because the augur will not spin, and this is when the part should be replaced. Customers found this to be an easy repair.

This is a genuine Kohler replacement part that has been sourced from the original manufacturer to be used with small engines. The metal screw is used to secure the head to the top of the cylinder assembly. This screw requires a hex ratchet set to install and is priced as a single item.

It is an OEM item that is made for use with Kohler engines commonly installed on a variety of lawn and garden equipment. This is the valve that the push rod ride inside of which will push the exhaust valve open during the exhaust stroke. A bent push rod or a damaged lifter-valve can not only affect your engine\\\'s performance, they can s...Read moreeriously damage other parts if the problem is not taken care of immediately. This is a high-quality replacement for a missing or a damaged component that was installed on a new unit. To ensure the correct location and installation of this item, refer to the diagrams of your specific model. Note, one durable metal lifter-valve and a tube of lube are included. You will need a screwdriver and a wrench set to take apart the engine when performing this repair.

This is an authentic Kohler replacement part that has been sourced from the original manufacturer to be used with small engines. The metal wing nut is used to secure the air cleaner assembly within the cover. This item is available as an individual replacement part.

This is a genuine OEM sourced spacer which is specially designed for use with Toro snowthrowers. It is an identical replacement for a missing or damaged spacer that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in ...Read moremind this high-quality component is made of durable metal and is sold individually.

A deck wheel that drags, wobbles, or has a flat spot may no longer protect the turf correctly. The smooth roller touches the ground when the mower deck passes over a raised area, helping prevent the blade from cutting deep patches. Check deck level and tire pressure first because poor adjustment can also cause scalping. Match the replacem...Read moreent using the complete mower model and serial number, and compare the bore, width, bracket spacing, and required hardware. Shut off the engine, remove the key, set the parking brake, and disconnect the spark plug before service. Support the deck securely, tighten the fastener properly, and make sure the wheel turns freely.

The governor cross shaft seal goes next to the plain washer. This part is made of plastic and is available individually. It is an authentic OEM sourced item which is specially produced for use with engines made by Kohler and Toro. A set of pliers may be required to replace this part if it becomes broken.

This item has been sourced from the original manufacturer to ensure quality. The metal screw is intended to be used with snowthrowers from Toro and Lawn-Boy. This screw is used to secure the bearing flange to the side of the auger housing. The screw is priced as a single item.

This Belleville washer, also called a disc spring or conical spring washer, is a component in your lawn equipment that distributes load and keeps tension in check in areas where controlled compression is needed such as in suspension systems and blade assemblies. If the washer is damaged, showing signs of deformation, cracks, or warping, y...Read moreour machine will have no cushioning between their parts and your machine will wear out faster. Use a pair of pliers or a flathead screwdriver to remove a washer from your machine. If it is stubborn, apply some penetrating oil to help loosen it. Remember to consult your user guide to determine how many washers you need and where they are in your machine. Since these washers are sold individually, it is strongly recommended that you replace all your washers in one go as they wear out at the same rate.