LXDT04CW Makita Impact Driver - Overview

The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the w...Read moreire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions.

Genuine Makita replacement part, this item is sold individually. This part is used on the tools listed below, to contain all of the part that are attached to the front end of the tool. Such as the Chuck assemblies on the the Impact Drivers and the Spindle Assemblies on the Screwdrivers.

This durable plastic latch is an original part sourced directly from Makita. This item is used to secure the drill case when closed. It is an identical replacement for a broken or missing latch that originally came with a new unit. Please see the appropriate diagram for your model to determine the correct location and application of this part. One item is included per order.

This is a Genuine OEM Sourced replacement part designed for Makita Impact Drivers. This part is made out of Metal and it is Sold Individually. This Washer helps to provide seal for the Sleeve. When replacing this part you would need a Screwdriver and Pliers.

This is a genuine item that is supplied directly from the original equipment manufacturer for use with Makita power tools. It is an identical replacement for a missing or damaged rubber pin that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and applicat...Read moreion of this hardware. Keep in mind this high-quality item is made of durable rubber material and is sold individually.

This is a genuine Makita replacement part, it is sold individually. It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers. Compatible with the tools listed below. The diameter is 3.5mm.

This is a Genuine OEM replacement part used on Makita drills and drivers. This is a metal spring and it is sold individually. Over time springs may lose its tension and may not function as intended. If this part is lost or damaged it must be replaced. To replace this spring a pair of pliers is needed.

This is an original replacement part manufactured for use with Makita impact drivers. The special bit sleeve is used to release, or lock in bits when changing the bits. The bit sleeve is available individually.

This is an authentic manufacturer sourced replacement assembly designed for use with Makita impact drivers. This part consists of: plastic holder ring, two (2) metal brush holders with springs and two (2) lead wires attached. This part holds carbon brushes around the armature to provide stable and safe contact. Please note carbon brushes ...Read moreare sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws holding the cover together. • Carefully remove two (2) halves of the housing to gain access to armature and brush holder. • Remove the screws holding brush holder to the trigger. • Remove the armature assembly and the brush holder. • Install the new brush holder, brushes and the armature • Reassemble and test your tool.

The anvil goes between the hammer and the nylon washer. This part is available as an individual replacement and is made of metal. It is a genuine Makita replacement part used in compatible impact drivers. A screwdriver may be required to replace this part if it becomes broken.

It is an authentic OEM component which is made for Makita impact drivers. This is the special lever which provides a user with a comfortable grip to change the rotation direction. If the part is damaged or is missing, this will provide an identical replacement for the original component that was installed on a new unit. The change lever i...Read mores made of durable plastic and is sold individually. To ensure the exact location and the correct replacement procedure, refer to the appropriate diagrams for your model. A screwdriver will be needed to take the housing apart to perform this repair.

This is an authentic OEM part. The Makita bumper is constructed of plastic, and has been designed for use with specific impact driver devices. This part secures the bit sleeve to the hammer case cover. The bumper is sold individually. A screwdriver is needed in making the replacement.