This handle screw, also known as a mounting bolt, is a mounting screw to help secure the door handle to your refrigerator door. If your handle is loose, you may just need to tighten the screw. If your screw is missing or broken, it may need to be replaced. There are multiple handle screws on your fridge, please consider ordering extra as ...Read morethey commonly wear at the same rate. This is about 1 inch long and metallic in color.
This is a genuine replacement switch. It is a push button style switch that is designed for use in your refrigerator. When the door of your appliance is opened the switch is released, and the light comes on. When you close the door the switch is pressed in, and the light turns off. You may need a putty knife to remove your old switch.
This part is the replacement ice tray for your refrigerator. The tray is made of white plastic and is approximately 9 inches in length, and 3 inches in width. It has the capacity for 8 ice cubes. The ice tray can be filled up with water and is the mold that shapes the ice cubes. If your current ice tray is cracked, warped, or if mineral d...Read moreeposits have settled inside it, it may cause the ice cubes to stick. This part is sold individually and is an authentic OEM part.
This condenser cooling fan motor is an essential component for maintaining your refrigerator’s performance. It circulates air over the condenser coils located at the back of the unit, helping to dissipate heat and regulate internal temperatures. Proper airflow prevents overheating and ensures efficient cooling. If your refrigerator is run...Read morening too warm or too cold, making unusual noises, or failing to start, the fan motor may need replacement. Installation typically involves disconnecting power, removing the rear access panel, and securing the new motor in place. Designed for durability, this part plays a critical role in keeping your appliance operating smoothly.
Restore consistent ice production in your refrigerator with this complete ice maker kit assembly, designed for select LG and Kenmore models. This genuine OEM component includes the ice maker unit and housing, engineered to deliver a reliable supply of ice for everyday use. If your current ice maker is malfunctioning or no longer producing...Read more ice, this replacement offers a dependable solution. Built for durability and precision, the assembly ensures proper fit and function. Installation typically requires basic tools and should be performed after confirming compatibility with your appliance’s model number.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The ice tray had warped and dumped water, which then froze down through the ice bucket and below.
8 of 8 peoplefound this instruction helpful.
George from ATLANTA, GA
Easy
Less than 15 mins
Screw drivers
To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting. Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards. The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and
... Read morethen insert the new tray. Proceed in reverse. Takes only a few minutes.
/Users/grf/Desktop/fridge ice tray.pdf
Read less
Was this helpful?
Thank you for voting!
Refrigerator did not run. It made several rapid clicks, then silent, then a minute later more clicks.
3 of 4 peoplefound this instruction helpful.
John from OCEAN SPRINGS, MS
A Bit Difficult
1- 2 hours
Pliers, Screw drivers
I removed the lower back panel. The difficulty and time consuming part was finding the old parts. They were inside a cover on the side of the motor. The cover was difficult to remove. It slides away from the motor. The terminals on the replacement parts were oriented differently from the original, Like a mirror image. Accordingly,
... Read more I reversed the wires (side to side) and connected them to the replacement parts. The refrigerator is now working fine.
I paid for the expedited shipping and they sent me a cheap knockoff attempt at the part that had the wrong size hole. So they refunded me the money I paid for the part but not the shipping, and then I crushed the part they sent me with a hammer and threw it away.