LS1030N Makita Miter Saw - Overview

Kerf boards (also called kerf plates) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf board for your tool can give a rough edge to the material you're cutting.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This switch activator button is a genuine Makita replacement part, It is sold individually. It has to be pressed to activate the power switch. This is a very common replacement part. It is advised to order one or two extra to keep on hand. This Makita switch button is compatible with the tools listed below, and it is not guaranteed to fit any other power tool models.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

It is a genuine item that is supplied by the original equipment manufacturer for use with Makita saws. This is an identical replacement for a missing or a faulty bolt that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.

Genuine OEM Replacement Part used on some Makita Saws. This part is Sold Individually. A switch handles the on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement.

This is an original hex flange head bolt sourced from Makita for use with compound miter saws. It is specifically designed to secure the center cover/plate to the safety guard. Includes one (1) bolt per order. Please note that to install or remove this bolt you would need a wrench.

This is a Genuine Manufacturer Sourced replacement part designed for use with Makita Miter Saws. It allows for the Guard to retract. This Torsion Spring is made out of Metal and it is sold individually. Replacing this item you would need a Screwdriver and Pliers.

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with miter saws. The clear plastic safety cover attaches to the center cover and blade case and is used to cover the bottom of the blade. This part is priced as a single item, please note the spring, hardware, and associative parts are separate.

This cord guard / strain reliever is a genuine Makita replacement part. It covers the final portion of cord before entering the tool, providing extra rigidness and preventing cord damage. Over time these cord guards break down and require replacement. The guard is constructed of heavy duty rubber compound for toughness. This cord guar...Read mored is compatible with the tools listed below. It is not guaranteed to fit any other power tool models.