LS1013FL Makita Miter Saw - Overview

This Kerf board is a genuine Makita replacement part. It is made of rigid plastic and has 2 screw holes to secure it to your saw. 2 of the Kerf Boards are required on the tools listed below. rnrnKerf boards (also called kerf plates) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf board for your tool can give a rough edge to the material you're cutting.

Genuine Manufacturer Sourced replacement part used on a variety of Makita Power Tools. This is a Metal Pan-Head Screw and it is sold individually. This screws is commonly used to hold two pieces of Housing Set together.

This is an OEM part sourced directly from the manufacturer. The hex bolt is designed for use in Makita miter saws and planer-jointers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different bolts used in the machine. Refer to the parts diagram to b...Read moree sure of ordering the correct part. You will require a wrench when replacing this part. This item is sold individually.

This switch activator button is a genuine Makita replacement part, It is sold individually. It has to be pressed to activate the power switch. This is a very common replacement part. It is advised to order one or two extra to keep on hand. This Makita switch button is compatible with the tools listed below, and it is not guaranteed to fit any other power tool models.

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric brak...Read moreing power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

This genuine Makita replacement part is designed for use with a variety of power tools. This screw is a standard hardware which has multiple applications based on your tool. It is made out of metal and it is sold individually. Would require a screwdriver to install or remove this screw.

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 8 Feet Long

This is a genuine OEM replacement part sourced directly from manufacturer. It is connected to the arm holder and it allows you to lock the saw in the needed position. This lever is made out of black plastic and it is sold individually. You would need a screwdriver to remove the screw that secures this lever.

Genuine Makita replacement part, this item is sold individually. The purpose of the Brush Holder Cap is to retain the brush in the brush holder. This Brush Cap is used on all the Makita models listed below. It is removed by using a slotted screwdriver Do not press too hard when removing the cap they do have a tendency to break.

This is an original replacement screw designed for use with Makita power tools. This is a standard hardware which has multiple uses based on equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

Genuine Makita replacement part, this part is sold individually. This screw is used to secure various internal and external parts in the tool models shown below. This is a pan-head phillips tapping screw.

This is a genuine OEM sourced replacement tapping screw which is specially designed for use with Makita power tools. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this item. This high-quality item is made of durable metal and it is sold individually.