The range thermostat is also commonly known as a stove, oven, cooktop, or range thermal fuse. This thermostat protects your oven from excessive heating, and will shut the oven heat off if excessive heating is detected. This is a genuine part sourced directly from the original manufacturer. You may need to replace this part if your applian...Read morece will not heat properly. It is made of metal and is approximately 1 inch in diameter. This part is sold individually. It is recommended to order a spare, especially if you commonly use the self-cleaning function in your oven.
This temperature sensor, also known as a thermistor, is compatible with various makes and types of appliances. This thermistor uses electrical currents to detect the interior temperature of the appliance it is in and by working with the control board, the board adjusts the level of cooling or heating through its heating or cooling element...Read more, depending on what is needed. If your appliance is being improperly heated or cooled, the temperature sensor may be to blame, and can be tested with a multimeter to check for continuity to see whether it is defective. Check your user manual for exact placement of this thermistor and any diagnostic information.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and forth. Installing this leg simply requires you to lift on the corner you are installing it under, and then screw it in place until your range is...Read more stable. This approximately 2-inch leveling leg is sold individually, so if your range has multiple legs that are broken or missing, consider how many legs you need to order.
The sub PCB assembly (also referred to as a relay board), is a part for your range. If your oven is overheating, this might indicate that your sub PCB assembly needs to be replaced. You will need a Phillips screwdriver to remove the screws securing the upper rear access panel brackets. Also, remove the screws securing the panel and detach...Read more. Take note of how the wires are currently connected to the board. This board is held in place by screws and can be removed. You will then need to release the retaining clips to release the entire board. The new sub PCB assembly should snap into place.
This radiant heater may also be known as a radiant surface element and is a part for your range. The function of this heater is to supply heat to the cooking area that is on the top of the range. This piece is roughly 9 inches long, and 7 inches wide. The most common symptom for needing to replace your radiant heater is if your burner is ...Read morenot heating. Before replacing this part, it is always a good idea to test it for continuity. To make this installation you will need a Phillips screwdriver, and a 14-inch nut driver.
This radiant surface element is a genuine OEM replacement for select LG electric ranges, designed to generate heat beneath the glass cooktop for a single burner. It ensures fast, even heating for efficient cooking and restores proper performance when an existing element is worn or damaged. Common signs of failure include burners that heat...Read more slowly, unevenly, or not at all, or visible damage to the element. Replacing this part helps maintain consistent cooking results and reliable operation. For safety, disconnect power before installation and handle the component carefully to avoid damage.
This oven and range display control board manages key cooking and control functions, acting as the main interface between the user and the appliance. It regulates oven temperature, controls cooking time and settings, and processes user inputs through the display and touch controls. When this component begins to fail, symptoms may include ...Read morea non-responsive or erratic display, inaccurate or fluctuating temperatures, or touch controls that do not respond as expected. Replacing a defective control board can restore accurate temperature regulation, reliable operation, and full control of oven functions.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No heat in oven mode
8 of 11 peoplefound this instruction helpful.
Dennis from CARY, IL
A Bit Difficult
More than 2 hours
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Verified P/N with LG. Took a few days . They sent names of several suppliers, cost was almost double. Ordered part from P/S, here in 2 days. Watched video on you tube. Unplugged, took off back, unplugged bake element, removed power box. The opening for bake element is still attached to rear panel by tiny bits of sheet metal. Used Dremel w
... Read moreith cut-off wheel to cut thru nibs & deburr opening. this panel has to be removed, it rests on bottom panel & is held in position by power box. Removed bake element carefully, front of element broken, tried to put new element in, would not fit. Had to grind notches in bottom panel down to clear supports on new element. This did the trick. back together quick & no problems. If had to do again estimate less than 1 hour.. By the way am 81 yrs. young.
Read less
Was this helpful?
Thank you for voting!
Oven would initially start to heat up but would not hold its temp
6 of 8 peoplefound this instruction helpful.
Leonard from Plano, TX
Really Easy
15 - 30 mins
Pliers, Screw drivers
I searched online and found someone that seemed to have the exact problem. That person had replaced the lower burner and the same PCB board I replaced. I was able to test the lower burner without removing it and it tested OK. The PCB board in the article I had checked was burned and obviously bad but mine was not. I took a chance and
... Read moreordered just the PCB board. I replaced this board and the oven now works perfectly. I seems this board was not turning on the bottom burner but the system thought it was working fine.
Read less
Was this helpful?
Thank you for voting!
Plastic cover on the control panel was cracking from high heat frying.
4 of 4 peoplefound this instruction helpful.
Charles from SARASOTA, FL
Really Easy
30 - 60 mins
Screw drivers
The two ribbon cables connecting the panel to the PC board slide into connectors on the PC board, these connectors have small tabs on each end that are pulled up to free the cable connection, then are pushed down to secure the new cable ends. Use a long Phillips bit on your screw gun to reach the screw at the bottom of the PC board.